Dacor OWD24 Planning Guides - Page 3

Document # PG02-002 ERWD, EWD, IWD, MRWD, MWDV, MWDH, OWD 24", 27", 30", 36", Wide Renaissance® Warming Drawers Revised 10/01/11 Page 3/3 PLANNING GUIDE Cabinet/countertop tolerances: +1/16" (+1.6 mm) -0 unless otherwise stated 36" typ. (91.4 cm) Warming drawer Warming drawer A B 27"/30"/36" Dacor single wall oven D Warming 120 Vac drawer elect. C D Warming 120 Vac drawer elect. C 120 Vac electrical outlet 3/4" min.* C (1.9 cm) D C 3/4" min.* (1.9 cm) Cooktop 36" typ. (91.4 cm) warning • Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. • This appliance must be installed in accordance with the accompanying installation instructions. Mounting platform must be 3/4" (1.9 cm) thick and support 100 lbs. 1 1/2" (3.8 cm) Typical countertop Warming drawer 3/4" min.* (1.9 cm) C 120 Vac A electrical B outlet Toe kick A 3/4" min.* (1.9 cm) Model ERWD27 ERWD30 EWD24 EWD27 EWD30 EWD36**** IWD24 IWD27 IWD30 MRWD27 MRWD30 MWDH27 MWDH30 MWDV27 MWDV30 OWD24***** (A) Cutout Width 25 1/2" (64.8 cm) 28 1/2" (72.4 cm) 22 1/2" (57.2 cm) 25 1/2" (64.8 cm) 28 1/2" (72.4 cm) 34 1/2" (87.6 cm) 22 1/2" (57.2 cm) 25 1/2" (64.8 cm) 28 1/2" (72.4 cm) 25 1/2" (64.8 cm) 28 1/2" (72.4 cm) 25 1/2" (64.8 cm) 28 1/2" (72.4 cm) 25 1/2" (64.8 cm) 28 1/2" (72.4 cm) 22 5/8" (57.5 cm) (B) Min. Width to Adjacent Doors/ Drawers 27 1/4" (69.2 cm)* 30 1/4" (76.8 cm)* 24 1/4" (61.6 cm)* 27 1/4" (69.2 cm)* 30 1/4" (76.8 cm)* 36 1/4" (92.1 cm)* ** ** ** 27" (68.6 cm)* 30" (76.2 cm)* 27 1/4" (69.2 cm)* 30 1/4" (76.8 cm)* 27 1/4" (69.2 cm)* 30 1/4" (76.8 cm)* 24 1/4" (61.6 cm)*** (C) Cutout Height 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 11 15/16" (30.3 cm) (D) Min. Vertical Gap Between Cutouts 1 1/4" (3.2 cm)* 1 1/4" (3.2 cm)* 1 1/4" (3.2 cm)* 1 1/4" (3.2 cm)* 1 1/4" (3.2 cm)* NA 1 1/16" (2.7 cm) 1 1/16" (2.7 cm) 1 1/16" (2.7 cm) 1 1/4" (3.2 cm)* 1 1/4" (3.2 cm)* 1 1/4" (3.2 cm)* 1 1/4" (3.2 cm)* 1 1/4" (3.2 cm)* 1 1/4" (3.2 cm)* NA Min. Cutout Depth 24" (61.0 cm) 20 1/8" (51.1 cm) * Bare minimum spacing to allow for ventilation and avoid scraping on ERWD, EWD, MRWD, MWDH and MWDV series models. ** On IWD series models or OWD24 without the optional front panel kit: The chassis and the drawer faceplate are smaller than the cutout. The custom front panel mounts to the drawer faceplate. The height and width of the custom front panel must exceed the appropriate cutout dimensions (A and C above) to cover the hole. Allow 1/4" minimum additional space on the top, bottom and sides from the custom front panel edge to prevent scraping against adjacent doors, drawers and the countertop. *** OWD24 with optional factory front panel kit only. Bare minimum spacing shown to avoid scraping. Gap above and below cutout is 3/4" minimum. See ** above for OWD24 with custom front panel. **** Model EWD36 cannot be installed above or below another warming drawer (any type). ***** Model OWD24 cannot be installed above, below or adjacent to a wall oven or warming drawer (any type). Specifications subject to change without notice. www.dacor.com Phone: (800) 7932-0.3093