Dell Alienware m15 R3 Service Manual - Page 41

Right I/O-board, Removing the right I/O-board

Get Dell Alienware m15 R3 PDF manuals and user guides View all Dell Alienware m15 R3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Steps 1. Using the alignment posts, adhere the keyboard-controller board into place on the palm-rest assembly. 2. Replace the two screws (M2x1.9) that secure the keyboard-controller board to the palm-rest assembly. 3. Connect the keyboard-controller board-cable to the keyboard-controller board and close the connector latch. 4. Connect the keyboard cable to the keyboard-controller board and close the connector latch. 5. Connect the keyboard-backlight cable to the keyboard-controller board and close the connector latch. Next steps 1. Install the battery. 2. Install the base cover. 3. Follow the procedure in After working inside your computer. Right I/O-board Removing the right I/O-board Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. 3. Remove the battery. 4. Remove the M.2 2230 solid-state drive. (if it is installed in the right M.2 slot) 5. Remove the M.2 2280 solid-state drive. (if it is installed in the right M.2 slot) About this task The following image(s) indicate the location of the right I/O-board and provides a visual representation of the removal procedure. 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Steps
1.
Using the alignment posts, adhere the keyboard-controller board into place on the palm-rest assembly.
2.
Replace the two screws (M2x1.9) that secure the keyboard-controller board to the palm-rest assembly.
3.
Connect the keyboard-controller board-cable to the keyboard-controller board and close the connector latch.
4.
Connect the keyboard cable to the keyboard-controller board and close the connector latch.
5.
Connect the keyboard-backlight cable to the keyboard-controller board and close the connector latch.
Next steps
1.
Install the
battery
.
2.
Install the
base cover
.
3.
Follow the procedure in
After working inside your computer
.
Right I/O-board
Removing the right I/O-board
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
base cover
.
3.
Remove the
battery
.
4.
Remove the
M.2 2230 solid-state drive
. (if it is installed in the right M.2 slot)
5.
Remove the
M.2 2280 solid-state drive
. (if it is installed in the right M.2 slot)
About this task
The following image(s) indicate the location of the right I/O-board and provides a visual representation of the removal procedure.
41