Dell Alienware m15 R4 Service Manual - Page 45

Install the M.2, Adhere the Mylar to the system board.

Get Dell Alienware m15 R4 PDF manuals and user guides View all Dell Alienware m15 R4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Steps 1. Using the alignment posts, place the right I/O-board in place on the palm-rest assembly. 2. Replace the two screws (M2x3) that secure the right I/O-board to the palm-rest asssembly. 3. Connect the speaker cable to the connector on the right I/O-board. 4. Using the alignment pins, connect the right I/O-board cable on the right I/O-board and the system board. NOTE: The I/O-board cable is polarity sensitive. To prevent damage to your computer ensure that the MB UMT end of the cable is connected to the system board. 5. Replace the two screws (M2x3) that secure the right I/O-board cable to the right I/O-board and system board. 6. Adhere the Mylar to the system board. Next steps 1. Install the M.2 2230 or 2280 solid-state drive, if one was installed in M.2 card slot 2. 2. Install the battery. 3. Install the base cover. 4. Follow the procedure in After working inside your computer. 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
Steps
1.
Using the alignment posts, place the right I/O-board in place on the palm-rest assembly.
2.
Replace the two screws (M2x3) that secure the right I/O-board to the palm-rest asssembly.
3.
Connect the speaker cable to the connector on the right I/O-board.
4.
Using the alignment pins, connect the right I/O-board cable on the right I/O-board and the system board.
NOTE:
The I/O-board cable is polarity sensitive. To prevent damage to your computer ensure that the MB UMT end of the
cable is connected to the system board.
5.
Replace the two screws (M2x3) that secure the right I/O-board cable to the right I/O-board and system board.
6.
Adhere the Mylar to the system board.
Next steps
1.
Install the M.2
2230
or
2280
solid-state drive, if one was installed in M.2 card slot 2.
2.
Install the
battery
.
3.
Install the
base cover
.
4.
Follow the procedure in
After working inside your computer
.
45