Dell DR4100 Symantec Backup Exec - Setting Up the DR Series System on Symantec - Page 38

Configuring the iSCSI target – Linux, Modify the following lines

Get Dell DR4100 PDF manuals and user guides View all Dell DR4100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

3.4 Configuring the iSCSI target - Linux Before you begin this procedure, ensure that the iSCSI initiator is installed (iscsi-initiator-utils). For example: yum install iscsi-initiator-utils ; /etc/init.d/iscsi start To configure the iSCSI target for Linux, follow these steps. 1. Add the CHAP Authentication details for the DR Series system on the Linux Initiator as follows: a. Edit /etc/iscsi/iscsid.conf and un-comment the following line: node.session.auth.authmethod = CHAP b. Modify the following lines: # To set a CHAP username and password for initiator # authentication by the target(s), uncomment the following lines: node.session.auth.username = iscsi_user node.session.auth.password = St0r@ge!iscsi 2. Set the Discovery Target Node(s) by using this command: iscsiadm -m discovery -t st -p For example: iscsiadm -m discovery -t st -p 10.8.230.108 38 Setting Up the Dell™ DR Series System on Symantec™ Backup Exec™ | April 2015

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
38
Setting Up the Dell™ DR Series System on Symantec™ Backup Exec™ | April 2015
3.4
Configuring the iSCSI target – Linux
Before you begin this procedure, ensure that the iSCSI initiator is installed (iscsi-initiator-utils). For
example:
yum install iscsi-initiator-utils ; /etc/init.d/iscsi start
To configure the iSCSI target for Linux, follow these steps.
1.
Add the CHAP Authentication details for the DR Series system on the Linux Initiator as follows:
a.
Edit /etc/iscsi/iscsid.conf and un-comment the following line:
node.session.auth.authmethod = CHAP
b.
Modify the following lines:
# To set a CHAP username and password for initiator
# authentication by the target(s), uncomment the following lines:
node.session.auth.username = iscsi_user
node.session.auth.password = St0r@ge!iscsi
2.
Set the Discovery Target Node(s) by using this command:
iscsiadm -m discovery -t st -p <IP or IQN of DR>
For example:
iscsiadm -m discovery -t st -p 10.8.230.108