Dell EqualLogic PS6210XS EqualLogic PS6210 Setup Poster - Page 1
Dell EqualLogic PS6210XS Manual
View all Dell EqualLogic PS6210XS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
Setting Up a PS Series Storage Array PS6210 Installation Before You Begin This poster is a condensed reference. Read the PS6210 Storage Arrays Installation and Setup Guide (provided in the box) for complete installation information. 4 Install the Array into a Rack Warning! The array is heavy. Do not attempt to lift the array without assistance. Mount the array into a four-post, 19-inch rack. Register for a Dell™ EqualLogic® Customer Support Account. If you do not have a customer service support account, go to eqlsupport.dell.com/secure/login.aspx and create one. 1. Slide the array onto the rails. 2. Hand-tighten the thumbscrews to the front of the rack. Download and Read the Release Notes from the Support Site. The PS Series Storage Arrays Release Notes contain the latest product information. Review Safety Guidelines. Review the safety instructions in your Safety, Environmental, and Regulatory Information booklet located in the shipping box. Prepare for Installation: Environmental requirements Make sure the installation location meets the power, cooling, and ventilation requirements described in the PS6210 Storage Arrays Installation and Setup Guide (located in the shipping box). Networking requirements - Standard Ethernet and TCP/IP networking rules apply to a PS Series SAN - 10 Gigabit Ethernet Hardware requirements (not supplied) - Standard 19-inch, four-post rack - For Ethernet connections (use a minimum of one 10GbE port per controller): With the 10GBASE-T port, CAT6 (or better) cable for up to 55 meters, CAT6A for up to 100 meters With the SFP+ port, optical cable or copper SFP+ cable - For Management connections (optional): CAT5 cable with RJ45 connector 1 Unpack the Shipping Box Caution: Protect sensitive hardware. Use an electrostatic wrist strap or a similar form of protection when handling hardware. Shipping box contents: Setup poster (this document) Rail kit (if ordered) Power cables Documentation PS Series Storage Array 2 Remove the Front Bezel 1. Using the bezel key, unlock the bezel. 2. Holding the bezel, lift the latch on the left side of the bezel and swing the left side away from the array. 3. Lift the right side of the bezel off the right side of the array. 4. Set the bezel aside. 3 Install the Rails into the Rack 1. Remove the rail kit from the shipping box. 2. Install the rails into the rack. See the Rack Installation setup poster for detailed instructions. SoftwarGeroCupo1 nfiguration Methods PS SerSieosfGtPrwoSuapsrSeeCrioensfigSutorartaiogne Arrays Multi-Member PS Series Group in RAID pRDoAelifIcaDyupltogliactyewSauybnetAmrraasykIPMaedmdrbeesrsname Step thTeofcoollnofwSiginutgreetpaAthbre2lreaPs:y.SCCSooenrlifleiegscusrotafttCwioaonren, yfioguunereadttihoeninfIonrmfaotiromn ation 1: Install the Host Integration Tools Step 3: Run the Remote Setup Wizard CHAP paCsHswAPorudpsaesrMsnweamomrbedpearsshAsiwdpmoridnisGtrraotuiopnIPGardodurpesnsame Group Configuration Step 4: Start Using the SAN Where to Go Next InstaPlSlaStiEoRnIE&SSSeTOtuRpAGMEanAuRaRlAYS 5 Install the Front Bezel 1. Hold the bezel with the array model number and Dell logo upright. 2. Hook the right end of the bezel onto the right side of the chassis. 3. Swing the left end of the bezel toward the left side of the chassis. 4. Press the bezel into place until the release latch closes. 5. Using the provided key, lock the front bezel. Store the key in a safe place.