Dell Inspiron 24 7459 Service Manual - Page 47

Replacing the USB board, Procedure, Post-requisites

Page 47 highlights

Replacing the USB board WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure 1 Align the screw hole on the USB board with the screw hole on the computer base. 2 Replace the screw that secures the USB board to the computer base. 3 Connect the USB-board cable to the USB board. 4 Route the USB-board cable through the routing clip on the computer base and close the routing clip. 5 Adhere the tape over the USB-board cable. Post-requisites 1 Follow the procedure from step 5 to step 8 in "Replacing the hard drive". 2 Replace the computer base. 3 Replace the wireless card. 4 Replace the base cover. 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101

Replacing the USB board
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in
Before working inside your computer
. After working inside your
computer, follow the instructions in
After working inside your
computer
. For more safety best practices, see the Regulatory
Compliance home page at www.dell.com/regulatory_compliance.
Procedure
1
Align the screw hole on the USB board with the screw hole on the
computer base.
2
Replace the screw that secures the USB board to the computer base.
3
Connect the USB-board cable to the USB board.
4
Route the USB-board cable through the routing clip on the computer
base and close the routing clip.
5
Adhere the tape over the USB-board cable.
Post-requisites
1
Follow the procedure from step 5 to step 8 in “
Replacing the hard drive
”.
2
Replace the
computer base
.
3
Replace the
wireless card
.
4
Replace the
base cover
.
47