Dell Inspiron 5491 AIO Inspiron 24-5491 Service Manual - Page 68

Troubleshooting, Enhanced Pre-Boot System Assessment (ePSA) diagnostics, Running the ePSA diagnostics

Get Dell Inspiron 5491 AIO PDF manuals and user guides View all Dell Inspiron 5491 AIO manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

5 Troubleshooting Enhanced Pre-Boot System Assessment (ePSA) diagnostics About this task The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware. The ePSA is embedded with the BIOS and is launched by the BIOS internally. The embedded system diagnostics provides a set of options for particular devices or device groups allowing you to: • Run tests automatically or in an interactive mode • Repeat tests • Display or save test results • Run thorough tests to introduce additional test options to provide extra information about the failed device(s) • View status messages that inform you if tests are completed successfully • View error messages that inform you of problems encountered during testing NOTE: Some tests for specific devices require user interaction. Always ensure that you are present at the computer terminal when the diagnostic tests are performed. Running the ePSA diagnostics Steps 1. Turn on your computer. 2. As the computer boots, press the F12 key as the Dell logo appears. 3. On the boot menu screen, select the Diagnostics option. 4. Click the arrow at the bottom left corner. Diagnostics front page is displayed. 5. Click the arrow in the lower-right corner to go to the page listing. The items detected are listed. 6. To run a diagnostic test on a specific device, press Esc and click Yes to stop the diagnostic test. 7. Select the device from the left pane and click Run Tests. 8. If there are any issues, error codes are displayed. Note the error code and validation number and contact Dell. Display built-in self test About this task The following procedure provides the instructions on how to run the built-in self test for the display: Steps 1. Turn off your computer. 2. Press and hold the display built-in self test button. 3. Press and hold the power button. 4. Release the power button. 68 Troubleshooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Troubleshooting
Enhanced Pre-Boot System Assessment (ePSA)
diagnostics
About this task
The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware. The ePSA is embedded with the
BIOS and is launched by the BIOS internally. The embedded system diagnostics provides a set of options for particular devices or device
groups allowing you to:
•
Run tests automatically or in an interactive mode
•
Repeat tests
•
Display or save test results
•
Run thorough tests to introduce additional test options to provide extra information about the failed device(s)
•
View status messages that inform you if tests are completed successfully
•
View error messages that inform you of problems encountered during testing
NOTE:
Some tests for specific devices require user interaction. Always ensure that you are present at the computer
terminal when the diagnostic tests are performed.
Running the ePSA diagnostics
Steps
1.
Turn on your computer.
2.
As the computer boots, press the F12 key as the Dell logo appears.
3.
On the boot menu screen, select the
Diagnostics
option.
4.
Click the arrow at the bottom left corner.
Diagnostics front page is displayed.
5.
Click the arrow in the lower-right corner to go to the page listing.
The items detected are listed.
6.
To run a diagnostic test on a specific device, press Esc and click
Yes
to stop the diagnostic test.
7.
Select the device from the left pane and click
Run Tests
.
8.
If there are any issues, error codes are displayed.
Note the error code and validation number and contact Dell.
Display built-in self test
About this task
The following procedure provides the instructions on how to run the built-in self test for the display:
Steps
1.
Turn off your computer.
2.
Press and hold the display built-in self test button.
3.
Press and hold the power button.
4.
Release the power button.
5
68
Troubleshooting