Dell M409WX User Guide - Page 26

LAMP, to use the projector at a lower power level 168 Watts.

Get Dell M409WX PDF manuals and user guides View all Dell M409WX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

LAMP Using the Lamp menu, you can adjust the display settings of your projectors. The Picture menu, provides the following options: LAMP HOUR-Displays the operating hours since the last lamp timer reset. POWER SAVING-Select Yes to set the Power Saving delay period. The delay period is the time you want the projector to wait without an input signal. By default, the delay period is set to 120 minutes. However, you can set this to 5 minutes, 15 minutes, 30 minutes, 45 minutes, 60 minutes, or 120 minutes. If an input signal is not detected during the delay period, the projector turns off the lamp and goes into power saving mode. If an input signal is detected when projector is in power saving mode, the projector automatically turns on. If an input signal is not detected within two hours, the projector switches from Power Saving mode to Power Off mode. To turn on the projector press the Power button. ECO MODE-Select On to use the projector at a lower power level (168 Watts). Operating at lower power levels may provide longer lamp life, quieter operation, and dimmer luminance output on the screen. Select Off to operate at normal power level (212 Watts). LAMP RESET-After you install a new lamp, select Yes to reset the lamp timer. QUICK SHUTDOWN-Select Yes to turn off the projector with a single press of the Power button. This function allows the projector to cool down within a short period of time by accelerating the fan speed. NOTE: If Quick Shutdown is enabled, expect a slightly higher acoustic noise during power off. 26 Using Your Projector

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
26
Using Your Projector
LAMP
Using the
Lamp
menu, you can adjust the display settings of your projectors. The
Picture menu, provides the following options:
L
AMP
H
OUR
—
Displays the
operating hours since the last
lamp timer reset.
P
OWER
S
AVING
—
Select
Yes
to
set the Power Saving delay
period. The delay period is
the time you want the
projector to wait without an
input signal. By default, the
delay period is set to 120
minutes. However, you can set this to 5 minutes, 15 minutes, 30 minutes, 45
minutes, 60 minutes, or 120 minutes.
If an input signal is not detected during the delay period, the projector turns off
the lamp and goes into power saving mode. If an input signal is detected when
projector is in power saving mode, the projector automatically turns on. If an input
signal is not detected within two hours, the projector switches from Power Saving
mode to Power Off mode. To turn on the projector press the Power button.
E
CO
M
ODE
—
Select
On
to use the projector at a lower power level (168 Watts).
Operating at lower power levels may provide longer lamp life, quieter operation,
and dimmer luminance output on the screen. Select
Off
to operate at normal
power level (212 Watts).
L
AMP
R
ESET
—
After you install a new lamp, select
Yes
to reset the lamp timer.
Q
UICK
S
HUTDOWN
—
Select
Yes
to turn off the projector with a single press of the
Power button. This function allows the projector to cool down within a short
period of time by accelerating the fan speed.
NOTE:
If Quick Shutdown is enabled, expect a slightly higher acoustic noise
during power off.