Dell OptiPlex 7071 Tower Tower Setup and specifications guide - Page 29

Post behavior

Get Dell OptiPlex 7071 Tower PDF manuals and user guides View all Dell OptiPlex 7071 Tower manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Option Deep Sleep Control Fan Control Override USB Wake Support Wake on LAN/WLAN Block Sleep Description This option determines how aggressively the system conserves power while shut down (SS) or in the Hibernate (S4) mode. The options are: • Disabled • Enabled in S5 only • Enabled in S4 and S5-enabled by default The option is not set by default Allows you to enable the USB devices to wake the computer from standby mode. The option "Enable USB Wake Support" is selected by default This option enables the computer to power up from the off state when triggered by a special LAN signal. This feature only works when the computer is connected to AC power supply. • Disabled - Does not enables the system to power on by special LAN signals when it receives a wake-up signal from the LAN or wireless LAN. • LAN or WLAN - Allows the system to be powered on by special LAN or wireless LAN signals. • LAN Only - Allows the system to be powered on by special LAN signals. • LAN with PXE Boot - A wakeup packet sent to the system in either the S4 or S5 state, that causes the system to wake up and immediately boot to PXE. • WLAN Only - Allows the system to be powered on by special WLAN signals. The Disabled option is enabled by default. Allows you to block entering to sleep (S3 state) in operating system environment. This option is disabled by default. Post behavior Table 31. POST Behavior Option Numlock LED Keyboard Errors Fast Boot Extend BIOS POST Time Full Screen Logo Warnings and Errors Description Allows you to enable or disable the Numlock feature when your computer starts. This option is enabled by default. Allows you to enable or disable the keyboard error reporting when the computer starts. The option Enable Keyboard Error Detection is enabled by default. This option can speed up the boot process by bypassing some compatibility steps: • Minimal - The system boots quickly, unless the BIOS has been updated, memory changed, or the previous POST did not complete. • Thorough - The system does not skip any steps in the boot process. • Auto - This allows the operating system to control this setting (this works only when the operating system supports Simple Boot Flag). This option is set to Thorough by default. This option creates an additional pre-boot delay. • 0 seconds (default) • 5 seconds • 10 seconds This option will display full screen logo if your image match screen resolution. The option Enable Full Screen Logo is not set by default. This option causes the boot process to only pause when warning or errors are detected. Choose any one of the option: • Prompt on Warnings and Errors (default) • Continue on Warnings • Continue on Warnings and Errors System setup 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
Option
Description
Deep Sleep Control
This option determines how aggressively the system conserves power while shut down (SS) or in
the Hibernate (S4) mode. The options are:
•
Disabled
•
Enabled in S5 only
•
Enabled in S4 and S5—enabled by default
Fan Control Override
The option is not set by default
USB Wake Support
Allows you to enable the USB devices to wake the computer from standby mode. The option
"
Enable USB Wake Support
" is selected by default
Wake on LAN/WLAN
This option enables the computer to power up from the off state when triggered by a special LAN
signal. This feature only works when the computer is connected to AC power supply.
•
Disabled
- Does not enables the system to power on by special LAN signals when it receives a
wake-up signal from the LAN or wireless LAN.
•
LAN
or
WLAN
- Allows the system to be powered on by special LAN or wireless LAN signals.
•
LAN Only
- Allows the system to be powered on by special LAN signals.
•
LAN with PXE Boot
- A wakeup packet sent to the system in either the S4 or S5 state, that
causes the system to wake up and immediately boot to PXE.
•
WLAN Only
- Allows the system to be powered on by special WLAN signals.
The
Disabled
option is enabled by default.
Block Sleep
Allows you to block entering to sleep (S3 state) in operating system environment. This option is
disabled by default.
Post behavior
Table 31. POST Behavior
Option
Description
Numlock LED
Allows you to enable or disable the Numlock feature when your computer starts. This option is
enabled by default.
Keyboard Errors
Allows you to enable or disable the keyboard error reporting when the computer starts. The option
Enable Keyboard Error Detection
is enabled by default.
Fast Boot
This option can speed up the boot process by bypassing some compatibility steps:
•
Minimal — The system boots quickly, unless the BIOS has been updated, memory changed, or
the previous POST did not complete.
•
Thorough — The system does not skip any steps in the boot process.
•
Auto — This allows the operating system to control this setting (this works only when the
operating system supports Simple Boot Flag).
This option is set to
Thorough
by default.
Extend BIOS POST Time
This option creates an additional pre-boot delay.
•
0 seconds
(default)
•
5 seconds
•
10 seconds
Full Screen Logo
This option will display full screen logo if your image match screen resolution. The option Enable Full
Screen Logo is not set by default.
Warnings and Errors
This option causes the boot process to only pause when warning or errors are detected. Choose any
one of the option:
•
Prompt on Warnings and Errors
(default)
•
Continue on Warnings
•
Continue on Warnings and Errors
System setup
29