Dell PowerConnect Brocade M5424 Brocade M5424 Blade Server SAN I/O QuickStart
Dell PowerConnect Brocade M5424 Manual
View all Dell PowerConnect Brocade M5424 manuals
Add to My Manuals
Save this manual to your list of manuals |
Dell PowerConnect Brocade M5424 manual content summary:
- Dell PowerConnect Brocade M5424 | Brocade M5424 Blade Server SAN I/O QuickStart - Page 1
53-1001081-01 September 29, 2008 M5424 SAN I/O Module QuickStart Guide - Dell PowerConnect Brocade M5424 | Brocade M5424 Blade Server SAN I/O QuickStart - Page 2
to identify, products or services of their respective owners. Notice: This document is for informational purposes only and does not set forth any warranty, expressed or implied, concerning any equipment, equipment feature, or service offered or to be offered by Brocade. Brocade reserves the right to - Dell PowerConnect Brocade M5424 | Brocade M5424 Blade Server SAN I/O QuickStart - Page 3
and configuration instructions, see the Brocade M5424 SAN I/O Module Hardware Reference Manual. NOTE Throughout this document, the M5424 SAN I/O Module is referred to as the SAN I/O Module. Unpacking and installing the SAN I/O Module If the SAN I/O Module is installed in the Blade Server - Dell PowerConnect Brocade M5424 | Brocade M5424 Blade Server SAN I/O QuickStart - Page 4
that use SAN I/O Module Command Line Interface (CLI) and the Web Tools application. For details refer to the Brocade Web Tools Administrator's Guide, Access Gateway Administrator's Guide, and Fabric OS Command Reference Manual. If the same operation can be performed using the Blade Server chassis - Dell PowerConnect Brocade M5424 | Brocade M5424 Blade Server SAN I/O QuickStart - Page 5
255.255.255.0. Reset the IP address using three methods. If the IP values are set using either of these methods, the IP values are stored on the SAN I/O Module. • SAN I/O Module Command Line Interface (CLI). • Blade Server Enclosure CMC CLI. • Blade Server Enclosure CMC graphical user interface (GUI - Dell PowerConnect Brocade M5424 | Brocade M5424 Blade Server SAN I/O QuickStart - Page 6
B1. • Switch-4 for SAN I/O Module installed in bay B2. • Switch-5 for SAN I/O Module installed in bay C1. • Switch-6 for SAN I/O module installed in bay C2. 3. At the login prompt, enter the default user name as "admin" and password as "password". 8 of 16 M5424 QuickStart Guide Publication Number - Dell PowerConnect Brocade M5424 | Brocade M5424 Blade Server SAN I/O QuickStart - Page 7
4. Use the appropriate CLI commands to change the IP address of the selected SAN I/O module. Refer to your Blade Server Enclosure CLI documentation. Using the CMC GUI to set the IP address To change the IP address, use the following steps: 1. Open the CMC application's Setup tab. 2. Enter the new - Dell PowerConnect Brocade M5424 | Brocade M5424 Blade Server SAN I/O QuickStart - Page 8
the ag -- modeShow command to determine the current operating mode. 1. If the SAN I/O Module is in Fabric OS Native mode, continue with step 2 and step 3. If the Module is in Access Gateway Mode, go on to step 4. 2. Log onto the SAN I/O Module through a Telnet connection, using the admin account - Dell PowerConnect Brocade M5424 | Brocade M5424 Blade Server SAN I/O QuickStart - Page 9
the "Operating the SAN I/O Module" chapter in the Brocade M5424 SAN Blade Server I/O Module Hardware Reference Manual. 7. Verify the correct operation of the SAN I/O Module by typing the switchShow command from the workstation. This command provides information about SAN I/O Module and port status - Dell PowerConnect Brocade M5424 | Brocade M5424 Blade Server SAN I/O QuickStart - Page 10
browser. 2. Enter the IP address of the SAN I/O Module into the Address field of the Web browser. See the Web Tools Administrator's Guide for more information on using Web Tools. 3. Log into Web Tools using the default administrative account. Login: admin Password: password 4. From the Fabric Tree - Dell PowerConnect Brocade M5424 | Brocade M5424 Blade Server SAN I/O QuickStart - Page 11
the CLI. 1. Log in using the default administrative account. Login: admin Password: password 2. Enter the following command to disable Fabric OS Native mode. switchDisable 3. Enter the following command to save the current configuration on the SAN I/O Module. This command is optional and is only - Dell PowerConnect Brocade M5424 | Brocade M5424 Blade Server SAN I/O QuickStart - Page 12
12 ports. Add optional POD licenses using either Brocade Web Tools or a Telnet connection; do not use the Blade Server Enclosure CMC software. Ports on Demand is ready to be unlocked in the SAN I/O Module firmware. A POD license might be supplied with SAN I/O Module software, or you can purchase - Dell PowerConnect Brocade M5424 | Brocade M5424 Blade Server SAN I/O QuickStart - Page 13
The Web browser must be connected to the same network as the SAN I/O Module. 2. Enter the IP address of the SAN I/O Module in the address field and press Enter. For more information about using Web Tools, see the Web Tools Administrator's Guide. M5424 QuickStart Guide Publication Number: 53-1001081 - Dell PowerConnect Brocade M5424 | Brocade M5424 Blade Server SAN I/O QuickStart - Page 14
16 of 16 M5424 QuickStart Guide Publication Number: 53-1001081-01
53-1001081-01
September 29, 2008
M5424 SAN I/O Module
QuickStart Guide