Dell PowerConnect W AP 93H Installation Guide - Page 2

Figure 8 Bracket to Gang Box (Standard US Single Gang Outlet Box Shown) 5. Connect any required cables to the rear of the W-AP93H. 6. Align the mounting posts on the mounting bracket with the corresponding mounting holes on the back of your W-AP93H as shown in Figure 9. Figure 9 W-AP93H to Bracket 7. Securing your W-AP93H to the mounting bracket using the enclosed security screw (see Figure 10). Figure 10 Securing the W-AP93H 8. If not using PoE, connect the AC-DC power adapter (sold separately) to the DC power socket located on the bottom of the W-AP93H. Verifying Post-Installation Connectivity The integrated LEDs on the AP can be used to verify that the AP is receiving power and initializing successfully (see Table 1). See the Dell PowerConnect W-Series ArubaOS Quick Start Guide at support.dell.com for further details on verifying postinstallation network connectivity Table 1 LED Behavior LED Color/State Meaning PWR ENET 0 Off Green flashing Red steady Green steady Off Green on Amber on Flashing No power to AP System initializing System failed to initialize, contact TAC Power on, device ready No link 1000 Mbps link 10/100 Mbps link ethernet link activity Table 1 LED Behavior (Continued) LED Color/State ENET 1-4 11A/N 11B/G/N Off Green on Flashing Off Amber Green Green flashing Off Amber Green Green flashing Meaning No link 10/100 Mbps link ethernet link activity 5 GHz radio is disabled 5 GHz radio enabled in WLAN mode 5 GHz radio enabled in 11n mode 5 GHz Air Monitor 2.4 GHz radio disabled 2.4 GHz radio enabled in WLAN mode 2.4 GHz radio enabled in 11n mode 2.4 GHz Air Monitor Configuring the W-AP93H AP Provisioning/Reprovisioning Provisioning parameters are unique to each AP. These local AP parameters are initially configured on the controller which are then pushed out to the AP and stored on the AP itself. It is recommended that provisioning settings be configured via the ArubaOS Web UI only. See the Dell PowerConnect W-Series ArubaOS User Guide at support.dell.com for complete details. AP Configuration Configuration parameters are network or controller specific and are configured and stored on the controller. Network configuration settings are pushed out to the AP(s) but remain stored on the controller. Configuration settings can be configured via the ArubaOS Web UI, ArubaOS CLI, or an Airwave Management Platform. See their respective guides for further details: the Dell PowerConnect W-Series ArubaOS User Guide or the Dell PowerConnect WAirwave User Guide at support.dell.com. Product Specifications Electrical  Ethernet:  1 x 10/100/1000Base-T auto-sensing ethernet RJ-45 Interface (ENET 0)  4 x 10/100Base-T auto-sensing ethernet RJ-45 Interfaces (ENET 1)  MDI/MDX  IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-T). IEEE 802.3ab (1000BaseT)  Power over ethernet (IEEE 802.3af compliant), 48V DC/350mA (see Figure 5 for pin configuration)  Power:  48V DC 802.3af Power over ethernet  12 VDC power interface, supports powering through an AC-to-DC power adapter Note: If a power adapter other than the one provided by Dell is used in the US or Canada, it should be NRTL Listed, with an output rated 12 VDC, minimum 1.25A, marked "LPS" or "Class 2," and suitable for plugging into a standard power receptacle in the US and Canada. For additional specifications on this product, please see the data sheet at dell.com. Proper Disposal of Dell Equipment For the most current information about Global Environmental Compliance and Dell products at dell.com. Waste of Electrical and Electronic Equipment Dell products at end of life are subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore are marked with the symbol shown at the left (crossedout wheelie bin). The treatment applied at end of life of these products in these countries shall comply with the applicable national laws of countries implementing Directive 2002/96EC on Waste of Electrical and Electronic Equipment (WEEE). European Union RoHS Dell products also comply with the EU Restriction of Hazardous Substances Directive 2002/95/EC (RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical and electronic equipment. Specifically, restricted materials under the RoHS Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some Dell products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies). Products and packaging will be marked with the "RoHS" label shown at the left indicating conformance to this Directive. China RoHS Dell products also comply with China environmental declaration 10 requirements and are labeled with the "EFUP 10" label shown at the left. Hazardous Materials Declaration Parts) 䪙 3E Hazardous Substance) ∲ +J 䬝 &G ݁Ӌ䫀 &U 3%% 3%'( PCA Boards) h ƻ ƻ ƻ ƻ ƻ Mechanical Sub-Assemblies) h ƻ ƻ ƻ ƻ ƻ SJ/T11363-2006 Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard.  h 6-7 Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard.  This table shows where these substances may be found in the supply chain of electronic information products, as of the date of sale of the enclosed product. The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are per the symbol shown here. The Environment- Friendly Use Period is valid only when the product is operated under the conditions defined in the product manual. Dell PowerConnect W-AP93H Access Point Installation Guide Contacting Support Web Site Support Main Site Support Site Dell Documentation dell.com support.dell.com support.dell.com/manuals Safety and Regulatory Compliance Dell provides a multi-language document that contains country-specific restrictions and additional safety and regulatory information for all Dell access points. This document can be viewed or downloaded at support.dell.com Caution: Dell access points must be installed by a professional installer. The professional installer is responsible for ensuring that grounding is available and it meets applicable local and national electrical codes. Caution: RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 7.87 inches (20cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. When operated in the 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use. EMC Compliance and Warning Statement This equipment generates, uses and can radiate radio frequency energy, and, if not installed and used in accordance with the manufacturer's instructions may cause harmful interference to other devices in the vicinity. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes interference with other devices, which may be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:  Reorient or relocate the device receiving the interference.  Increase the separation between the equipment.  Connect the equipment into an outlet on a circuit different from that to which the other device(s) are connected.  Consult the manufacturer or field service technician for help. The protection against electric shock is Class ll. Equipment not suitable for use in the presence of flammable mixtures. Copyright © 2012 Aruba Networks, Inc. Aruba Networks trademarks include , Aruba Networks®, Aruba Wireless Networks®, the registered Aruba the Mobile Edge Company logo, and Aruba Mobility Management System®. Dell™, the DELL™ logo, and PowerConnect™ are trademarks of Dell Inc. All rights reserved. Specifications in this manual are subject to change without notice. Originated in the USA. All other trademarks are the property of their respective owners. Open Source Code Certain Aruba products include Open Source software code developed by third parties, including software code subject to the GNU General Public License (GPL), GNU Lesser General Public License (LGPL), or other Open Source Licenses. The Open Source code used can be found at this site: http://www.arubanetworks.com/open_source Legal Notice The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate other vendors' VPN client devices constitutes complete acceptance of liability by that individual or corporation for this action and indemnifies, in full, Aruba Networks, Inc. from any and all legal actions that might be taken against it with respect to infringement of copyright on behalf of those vendors. 200202320G TRA REGISTERED No: ER0083046/12 DEALER No: DA0039425/10 www.Dell.com Dell PowerConnect W-AP93H Access Point | Installation Guide Part Number 0511057-02 | March 2012