Dell PowerEdge 2600 Installing or Replacing an ERA/O Card - Page 9

Installation and, Troubleshooting Guide - server

Get Dell PowerEdge 2600 PDF manuals and user guides View all Dell PowerEdge 2600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

10 Reinstall the front fan assembly: a Place the fan assembly in the hinge bracket and swing the fan assembly down until the release lever snaps into place. b Connect the fan assembly power cable to the front fan connector on the SCSI backplane board. 11 Replace the system cover. See "Replacing the Cover" in your Installation and Troubleshooting Guide. NOTE: If the server management Ethernet connector has not been used before, remove the cover that protects the connector before connecting a network cable. See Figure 1-6 for the location of the connector. 12 Connect a network cable to the 10-Mbps server management Ethernet connector on the system back panel. See Figure 1-6. Figure 1-6. Server Management Ethernet Connector server management Ethernet connector 13 Reconnect the system and peripherals to their electrical outlets, and turn them on. 14 Close the bezel. 15 Update the ERA/O card with the latest version of the ERA/O firmware, available at the Dell Support website at support.dell.com. See the RAC documentation provided on the documentation CD for information about updating the firmware. Installing or Replacing an ERA/O Card 1-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
Installing or Replacing an ERA/O Card
1-7
10
Reinstall the front fan assembly:
a
Place the fan assembly in the hinge bracket and swing the fan assembly down until
the release lever snaps into place.
b
Connect the fan assembly power cable to the front fan connector on the SCSI
backplane board.
11
Replace the system cover. See "Replacing the Cover" in your
Installation and
Troubleshooting Guide
.
NOTE:
If the server management Ethernet connector has not been used before,
remove the cover that protects the connector before connecting a network cable. See
Figure 1-6 for the location of the connector
.
12
Connect a network cable to the 10-Mbps server management Ethernet connector on
the system back panel. See Figure 1-6.
Figure 1-6.
Server Management Ethernet Connector
13
Reconnect the system and peripherals to their electrical outlets, and turn them on.
14
Close the bezel.
15
Update the ERA/O card with the latest version of the ERA/O firmware, available at the
Dell Support website at
support.dell.com
.
See the RAC documentation provided on the documentation CD for
information about updating the firmware.
server management
Ethernet connector