Dell PowerEdge VRTX VRTX Enclosure Owner's Manual - Page 27

Initial System Configuration, Before You Begin, Initial Setup Sequence

Get Dell PowerEdge VRTX PDF manuals and user guides View all Dell PowerEdge VRTX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

2 Initial System Configuration Before You Begin CAUTION: The enclosure power supplies must be connected to a PDU or to an electrical outlet. The power supplies require a 100 V to 120 V or 200 V to 240 V power source. You can select only one AC power input, as the system does not operate at both ranges simultaneously. • Your system supports Dell PowerEdge M520 and M620 server modules that are specifically configured for the enclosure, and can be identified by a label marked PCIe on the server module. If you install PowerEdge M520 and M620 server modules that are not configured for the enclosure, an error message is displayed. For more information on configuring a server module for the enclosure, see Configuring A Server Module. • Ensure that you have downloaded the latest BIOS on the server module(s) from dell.com/support. • Update all PCIe mezzanine card firmware and iDRAC firmware on the server module(s). • Download the latest version of CMC firmware from dell.com/support. Also, make sure that you have the Dell Systems Management Tools and Documentation DVD that was included with your system. • If your network uses static addressing, you need the IP address, subnet mask, and gateway to configure the CMC and other modules in the enclosure. Initial Setup Sequence CAUTION: To maintain optimum thermal conditions, ensure that there are no obstructions to airflow on the front and back of the enclosure. The front and back of the enclosure must have at least 30 cm (12 inches) and 61 cm (24 inches) of unobstructed space respectively. • Unpack the enclosure and the server module(s) and identify each item. For more information, see the Getting Started Guide and Rack Installation Guide at dell.com/poweredgemanuals. • The tower system has four feet on its bottom panel that can be extended outward to help properly stabilize the system. You can also install the optional wheel assembly. For more information, see Installing The Wheel Assembly. WARNING: Failure to extend the system feet outward poses the risk of having the system tip over, possibly causing bodily injury or damage to the system. CAUTION: Rolling the system on its wheels can cause vibrations that can damage the system. • If you are using the optional rack configuration, assemble the rails and install the system in the rack following the safety instructions and the rack installation instructions provided with your system. For more information on converting the system to rack mode, see Converting The System From Tower Mode To Rack Mode. 1. Install the server module(s). CAUTION: Do not turn on the server module(s) until you have configured the I/O module. 2. Connect the network cable to the I/O module to provide network connection to the server. NOTE: If you have a pass-through module installed in the enclosure, each server module requires its own network cable. 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
2
Initial System Configuration
Before You Begin
CAUTION: The enclosure power supplies must be connected to a PDU or to an electrical outlet. The power
supplies require a 100 V to 120 V or 200 V to 240 V power source. You can select only one AC power input, as the
system does not operate at both ranges simultaneously.
•
Your system supports Dell PowerEdge M520 and M620 server modules that are specifically configured for the
enclosure, and can be identified by a label marked PCIe on the server module. If you install PowerEdge M520
and M620 server modules that are not configured for the enclosure, an error message is displayed. For more
information on configuring a server module for the enclosure, see
Configuring A Server Module
.
•
Ensure that you have downloaded the latest BIOS on the server module(s) from
dell.com/support
.
•
Update all PCIe mezzanine card firmware and iDRAC firmware on the server module(s).
•
Download the latest version of CMC firmware from
dell.com/support
. Also, make sure that you have the
Dell
Systems Management Tools and Documentation
DVD that was included with your system.
•
If your network uses static addressing, you need the IP address, subnet mask, and gateway to configure the
CMC and other modules in the enclosure.
Initial Setup Sequence
CAUTION: To maintain optimum thermal conditions, ensure that there are no obstructions to airflow on the front
and back of the enclosure. The front and back of the enclosure must have at least 30 cm (12 inches) and 61 cm (24
inches) of unobstructed space respectively.
•
Unpack the enclosure and the server module(s) and identify each item. For more information, see the
Getting
Started Guide
and
Rack Installation Guide
at
dell.com/poweredgemanuals
.
•
The tower system has four feet on its bottom panel that can be extended outward to help properly stabilize the
system. You can also install the optional wheel assembly. For more information, see
Installing The Wheel
Assembly
.
WARNING: Failure to extend the system feet outward poses the risk of having the system tip over, possibly
causing bodily injury or damage to the system.
CAUTION: Rolling the system on its wheels can cause vibrations that can damage the system.
•
If you are using the optional rack configuration, assemble the rails and install the system in the rack following
the safety instructions and the rack installation instructions provided with your system. For more information on
converting the system to rack mode, see
Converting The System From Tower Mode To Rack Mode
.
1.
Install the server module(s).
CAUTION: Do not turn on the server module(s) until you have configured the I/O module.
2.
Connect the network cable to the I/O module to provide network connection to the server.
NOTE:
If you have a pass-through module installed in the enclosure, each server module requires its own
network cable.
27