Dell PowerStore 3000X EMC PowerStore Power Down and Reboot Procedures Guide - Page 12

Reboot a PowerStore T model node using a service script, Reboot a PowerStore X model node

Get Dell PowerStore 3000X PDF manuals and user guides View all Dell PowerStore 3000X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

7. Enable support notifications as described in Enable support notifications on page 19. Reboot a PowerStore T model node using a service script Prerequisites Obtain the following information: • Management IP address of the appliance that contains the node. In PowerStore Manager, go to Settings > Networking > Networking IPs > Management. Review the Management IPs table to identify the management IP address associated with the appliance. • Service account credentials NOTE: Do not power off or reboot a node, if the peer node is not operating normally. If the peer node is experiencing any major issues, associated alerts and events appear in PowerStore Manager. Also, to avoid service interruptions, ensure that there are sufficient and healthy paths from all connected hosts to the peer node. About this task Use the following procedure to reboot a PowerStore T model node using a service script: Steps 1. Disable support notifications as described in Disable support notifications on page 19. 2. Launch an SSH client, and connect to the appliance using the management IP address. 3. Enter the username and password for the service account to log in. The login prompt indicates the node that you are logged into. For example, the letter "A" in the prompt [SVC:user@FNM12345678910-A~]$ indicates that you are logged into node A. 4. Based on the node you are logged into, run one of the following commands: • svc_node reboot local to reboot the node you are logged into. • svc_node reboot peer to reboot the peer node. For more information, see the PowerStore Service Scripts Guide. 5. Enable support notifications as described in Enable support notifications on page 19. Reboot a PowerStore X model node Prerequisites Obtain the following information: • Address of the VMware vCenter server associated with the appliance • Associated vCenter server account credentials NOTE: Do not power off or reboot a node, if the peer node is not operating normally. If the peer node is experiencing any major issues, associated alerts and events appear in PowerStore Manager. Also, to avoid service interruptions, ensure that there are sufficient and healthy paths from all connected hosts to the peer node. About this task Use the following procedure to reboot a PowerStore X model node: Steps 1. Disable support notifications as described in Disable support notifications on page 19. 2. Log in to the associated vCenter server. 12 Power control procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
7.
Enable support notifications as described in
Enable support notifications
on page 19.
Reboot a PowerStore T model node using a service script
Prerequisites
Obtain the following information:
•
Management IP address of the appliance that contains the node. In PowerStore Manager, go to
Settings
>
Networking
>
Networking IPs
>
Management
. Review the
Management IPs
table to identify the management IP address associated with the
appliance.
•
Service account credentials
NOTE:
Do not power off or reboot a node, if the peer node is not operating normally. If the peer node is experiencing any
major issues, associated alerts and events appear in PowerStore Manager.
Also, to avoid service interruptions, ensure that there are sufficient and healthy paths from all connected hosts to the
peer node.
About this task
Use the following procedure to reboot a PowerStore T model node using a service script:
Steps
1.
Disable support notifications as described in
Disable support notifications
on page 19.
2.
Launch an SSH client, and connect to the appliance using the management IP address.
3.
Enter the username and password for the service account to log in.
The login prompt indicates the node that you are logged into. For example, the letter
"A"
in the prompt
[SVC:user@FNM12345678910-A~]$
indicates that you are logged into node A.
4.
Based on the node you are logged into, run one of the following commands:
•
svc_node reboot local
to reboot the node you are logged into.
•
svc_node reboot peer
to reboot the peer node.
For more information, see the
PowerStore Service Scripts Guide
.
5.
Enable support notifications as described in
Enable support notifications
on page 19.
Reboot a PowerStore X model node
Prerequisites
Obtain the following information:
•
Address of the VMware vCenter server associated with the appliance
•
Associated vCenter server account credentials
NOTE:
Do not power off or reboot a node, if the peer node is not operating normally. If the peer node is experiencing any
major issues, associated alerts and events appear in PowerStore Manager.
Also, to avoid service interruptions, ensure that there are sufficient and healthy paths from all connected hosts to the
peer node.
About this task
Use the following procedure to reboot a PowerStore X model node:
Steps
1.
Disable support notifications as described in
Disable support notifications
on page 19.
2.
Log in to the associated vCenter server.
12
Power control procedures