Dell Precision 410 Dell Precision WorkStation 410 Systems Service Manual - Page 55

Incorrect Time or Date

Get Dell Precision 410 PDF manuals and user guides View all Dell Precision 410 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

System halted Terminator/ processor card not installed! System halted! Time-of-day clock stopped Time-of-day not set Timer chip counter 2 failed WARNING: Dell's Disk Monitoring System has detected that drive [0/1] on the [0/1] EIDE controller is operating outside of normal specifications. It is advisable to immediately back up your data and replace your hard-disk drive by calling your support desk or Dell Computer Corporation. Write fault Write fault on selected drive System locked up because the processor is not the correct revision. System processor is not a type supported by Dell and more than 512 MB of RAM is installed. System does not have terminator card or secondary processor. Terminator card or secondary processor is improperly installed or is not installed. System battery is low. Defective battery or faulty chip (defective system board). Time or Date settings in System Setup program are incorrect, or the system battery does not work. Incorrect Time or Date settings, or defective system battery. Timer circuit on system Defective system board. board is malfunctioning. POST queried EIDE drive for status. Drive detected possible error conditions. Unreliable or defective drive. MS-DOS cannot write to diskette or hard-disk drive. Faulty diskette or harddisk drive. Beep Codes and Error Messages 3-11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
Beep Codes and Error Messages
3-11
System halted
System locked up
because the processor
is not the correct
revision.
System processor is not
a type supported by Dell
and more than 512 MB of
RAM is installed.
Terminator/
processor card
not installed!
System halted!
System does not have
terminator card or
secondary processor.
Terminator card or
secondary processor is
improperly installed or is
not installed.
Time-of-day
clock stopped
System battery is low.
Defective battery or
faulty chip (defective sys-
tem board).
Time-of-day not
set
Time or Date settings in
System Setup program
are incorrect, or the sys-
tem battery does not
work.
Incorrect Time or Date
settings, or defective sys-
tem battery.
Timer chip
counter 2
failed
Timer circuit on system
board is malfunctioning.
Defective system board.
WARNING: Dell’s
Disk Monitor-
ing System has
detected that
drive [0/1] on
the [0/1] EIDE
controller is
operating out-
side of normal
specifica-
tions. It is
advisable to
immediately
back up your
data and
replace your
hard-disk drive
by calling your
support desk or
Dell Computer
Corporation.
POST queried EIDE
drive for status. Drive
detected possible error
conditions.
Unreliable or defective
drive.
Write fault
Write fault on
selected drive
MS-DOS cannot write
to diskette or hard-disk
drive.
Faulty diskette or hard-
disk drive.