Dell S5296F-ON EMC Networking OS10 Enterprise Edition Switch Configuration Gui - Page 25

Con interfaces

Page 25 highlights

S5148F-Leaf1A description VM_Network_B no shutdown S5148F-Leaf1B description VM_Network_B no shutdown 7.1.3 Configure interfaces Configure the interfaces for the jump box or laptop computer connections to be used during VxRail deployment. This example uses interface 1/1/9 on each switch. While only one connection is required, two are used for redundancy. Add these interfaces as access ports on VLAN 1611 (the in-band management VLAN). Note: In this example, the jump box also provides DNS and NTP services as covered in Section 5.4. If these services are located on other devices, ensure the switch interfaces connected to these services are configured in the same manner. Configure the interfaces for connections to the VxRail nodes. Interfaces 1/1/17 through 1/1/20 are used in this example. Use the switchport mode trunk command to enable ports to carry traffic for multiple VLANs. Configure the ports as access (untagged) ports on VLAN 1611 (the in-band management VLAN). Configure the ports as trunk (tagged) ports on VLANs 1612-1615 (the vMotion, vSAN, and VM Network VLANs). Configure ports directly connected to nodes, servers, or other endpoints as STP edge ports. Enable flow control on node-connected ports for best performance. Note: Flow control is enabled on all network interfaces in ESXi by default. For more information, see VMware vSAN Network Design. Configure interfaces - dual switch with VLT S5148F-Leaf1A S5148F-Leaf1B interface ethernet1/1/9 description JumpBox_DNS switchport access vlan 1611 spanning-tree port type edge no shutdown interface ethernet1/1/9 description JumpBox_DNS switchport access vlan 1611 spanning-tree port type edge no shutdown interface ethernet1/1/17 description Node1_Port1 switchport mode trunk switchport access vlan 1611 switchport trunk allowed vlan 16121615 spanning-tree port type edge flowcontrol receive on flowcontrol transmit on no shutdown interface ethernet1/1/17 description Node1_Port2 switchport mode trunk switchport access vlan 1611 switchport trunk allowed vlan 16121615 spanning-tree port type edge flowcontrol receive on flowcontrol transmit on no shutdown interface ethernet1/1/18 description Node2_Port1 switchport mode trunk switchport access vlan 1611 interface ethernet1/1/18 description Node2_Port2 switchport mode trunk switchport access vlan 1611 25 Dell EMC Networking OS10 Enterprise Edition Switch Configuration Guide for VxRail featuring S5248F-ON, S5232F-ON and S5148F-ON

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53

25
Dell EMC Networking OS10 Enterprise Edition Switch Configuration Guide for VxRail featuring S5248F-ON,
S5232F-ON and S5148F-ON
S5148F-Leaf1A
S5148F-Leaf1B
description VM_Network_B
no shutdown
description VM_Network_B
no shutdown
7.1.3
Configure interfaces
Configure the interfaces for the jump box or laptop computer connections to be used during VxRail
deployment. This example uses interface 1/1/9 on each switch. While only one connection is required, two are
used for redundancy. Add these interfaces as access ports on VLAN 1611 (the in-band management VLAN).
Note:
In this example, the jump box also provides DNS and NTP services as covered in Section 5.4.
If these
services are located on other devices, ensure the switch interfaces connected to these services are
configured in the same manner.
Configure the interfaces for connections to the VxRail nodes. Interfaces 1/1/17 through 1/1/20 are used in this
example.
Use the
switchport mode trunk
command to enable ports to carry traffic for multiple VLANs. Configure
the ports as access (untagged) ports on VLAN 1611 (the in-band management VLAN). Configure the ports as
trunk (tagged) ports on VLANs 1612-1615 (the vMotion, vSAN, and VM Network VLANs).
Configure ports directly connected to nodes, servers, or other endpoints as STP edge ports. Enable flow
control on node-connected ports for best performance.
Note:
Flow control is enabled on all network interfaces in ESXi by default. For more information, see
VMware
vSAN Network Design
.
Configure interfaces – dual switch with VLT
S5148F-Leaf1A
S5148F-Leaf1B
interface ethernet1/1/9
description JumpBox_DNS
switchport access vlan 1611
spanning-tree port type edge
no shutdown
interface ethernet1/1/17
description Node1_Port1
switchport mode trunk
switchport access vlan 1611
switchport trunk allowed vlan 1612-
1615
spanning-tree port type edge
flowcontrol receive on
flowcontrol transmit on
no shutdown
interface ethernet1/1/18
description Node2_Port1
switchport mode trunk
switchport access vlan 1611
interface ethernet1/1/9
description JumpBox_DNS
switchport access vlan 1611
spanning-tree port type edge
no shutdown
interface ethernet1/1/17
description Node1_Port2
switchport mode trunk
switchport access vlan 1611
switchport trunk allowed vlan 1612-
1615
spanning-tree port type edge
flowcontrol receive on
flowcontrol transmit on
no shutdown
interface ethernet1/1/18
description Node2_Port2
switchport mode trunk
switchport access vlan 1611