Dell W-Series 205H W-AP205H Access Point Installation Guide - Page 2

5. Insert the two included machine screws and tighten them to secure the mounting bracket. Figure 6 Bracket to Gang Box (US Single Gang Outlet Box Shown) Figure 7 Bracket to Gang Box (Worldwide Single Gang Outlet Box Shown) 6. Connect the cables to the back of the AP. 7. Align the mounting slots on the back of the AP with the corresponding mounting posts on the wall mount as shown in Figure 8. 8. Push the AP against the posts and downward until the posts engage the slots at the top of the slots. Figure 8 AP to Bracket 9. Once the AP is fastened onto the wall mount, insert the T8H Torx Security Screw into the hole located on the upper-right edge of the wall mount and tighten. 10. If not using PoE, connect the AC-DC power adapter (sold separately) to the DC power socket located on the side of the AP. Verifying Post-Installation Connectivity The System Status LED on the AP can be used to verify that the AP is receiving power and initializing successfully (LED). Refer to the Dell Networking W-Series ArubaOS Quick Start Guide for further details on verifying post-installation network connectivity. Configuring the AP AP Provisioning/Reprovisioning Provisioning parameters are unique to each AP. These local AP parameters are initially configured on the controller which are then pushed out to the AP and stored on the AP itself. It is recommended that the provisioning settings be configured via the ArubaOS Web UI only. Refer to the Dell Networking W-Series ArubaOS User Guide for complete details. AP Configuration Configuration parameters are network or controller specific and are configured and stored on the controller. Network configuration settings are pushed out to the AP(s) but remain stored on the controller. Configuration settings can be configured via the ArubaOS Web UI or CLI. Refer to Dell Networking W-Series ArubaOS User Guide and/or the Dell Networking W-Series ArubaOS CLI Reference Guide for details. Product Specifications Electrical  Ethernet:  4x 10/100/1000 Base-T auto-sensing Ethernet RJ-45 Interface (E0-E3)  2x passive RJ-45 Pass-Through interface (E0/PT and PT)  MDI/MDX  IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-T). IEEE 802.3ab (1000Base-T)  Power over Ethernet (IEEE 802.3af and 802.3at compliant), 48VDC (nominal) and 56VDC (maximum)/350mA (see Figure 4 for pin configuration)  Power:  48VDC power interface, supports powering through an AC-to-DC power adapter  PoE support on Ethernet ports: 802.3af-compliant PoE sourcing device NOTE: If a power adapter other than the one provided by Dell is used in US or Canada, it should be NRTL Listed, with an output rated 48VDC, minimum 0.75A, marked "LPS" and "Class 2", and suitable for plugging into a standard power receptacle in the US and Canada. For additional specifications on this product, please refer to the product data sheet on dell.com. Proper Disposal of Dell Equipment Dispose of Dell products per local regulation. For the most current information about Global Environmental Compliance and Dell products, see our website at dell.com. Waste of Electrical and Electronic Equipment Dell products at end of life are subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore are marked with the symbol shown at the left (crossed-out wheelie bin). The treatment applied at end of life of these products in these countries shall comply with the applicable national laws of countries implementing Directive 2002/96EC on Waste of Electrical and Electronic Equipment (WEEE). India RoHS This product complies with RoHS requirements as prescribed by E-Waste (Management & Handling) Rules, governed by the Ministry of Environment & Forests, Government of India. European Union RoHS Dell products also comply with the EU Restriction of Hazardous Substances Directive 2011/65/EC (RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical and electronic equipment. Specifically, restricted materials under the RoHS Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some Dell products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies). Products and packaging will be marked with the "RoHS" label shown at the left indicating conformance to this directive. China RoHS 10 Dell products also comply with China environmental declaration requirements and are labeled with the "EFUP 10" label shown at the left. Hazardous Materials Declaration Parts) 䪙 3E Hazardous Substance) ∲ +J 䬝 &G ݁Ӌ䫀 &U 3%% 3%'( PCA Boards) h ƻ ƻ ƻ ƻ ƻ Mechanical Sub-Assemblies) h ƻ ƻ ƻ ƻ ƻ SJ/T11363-2006 Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard.  h 6-7 Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard.  This table shows where these substances may be found in the supply chain of electronic information products, as of the date of sale of the enclosed product. The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are per the symbol shown here. The Environment- Friendly Use Period is valid only when the product is operated under the conditions defined in the product manual. Safety and Regulatory Compliance NOTE: For country specific restrictions and additional safety and regulatory information, refer to the multi-language Dell Networking W-Series Safety, Environmental, and Regulatory Information document included with your Dell Networking controller. Regulatory Model Name The regulatory model name of W-AP205H is APINH205 FCC CAUTION: Dell access points must be installed by a professional installer. The professional installer is responsible for ensuring that grounding is available and it meets applicable local and national electrical codes. This device is electronically labeled. To view the FCC ID: 1. Log into the controller WebUI. 2. Navigate to the Maintenance > Controller > About. CAUTION: RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 7.87 inches (20 cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. When operated in the 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the potential for harmful interference with co-channel Mobile Satellite Systems. Equipment not suitable for use in the presence of flammable mixtures. CAUTION: RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 7.87 inches (20cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FCC Class B Part 15 This device complies with Part 15 of the Federal Communications Commission (FCC) Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer's instructions, may cause interference harmful to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio or TV technician for help. EU Regulatory Conformance This product is CE marked according to the provisions of the R & TTE Directive (1999/5/ EC) - CE(!). Dell hereby declares that the APINH205 device model is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC -CE(!) The Declaration of Conformity made under Directive 1999/5/EC is available for viewing at the following location: dell.com. Canadian Statement Complies with the Class B limits for radio noise emissions as set out in the interference-causing equipment standard entitled "Digital Apparatus," ICES-003 of Industry Canada. Cet apareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel brouilleur du Canada. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Déclaration d'Industrie Canada Conformément aux réglementations d'Industrie Canada, cet émetteur-récepteur radio doit être utilisé uniquement avec une antenne dont le type et le gain maximal doivent être approuvés par Industrie Canada. Pour réduire les interférences radio potentielles, le type d'antenne et son gain doivent être choisis de façon à ce que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas les valeurs nécessaires à une communication efficace. Ce périphérique est conforme aux règlements RSS exempts de licence d'Industrie Canada. L'utilisation de ce périphérique est soumise aux deux conditions suivantes : (1) ce périphérique ne doit pas provoquer d'interférences, et (2) ce périphérique doit accepter toute interférence, y compris les interférences susceptibles de provoquer un dysfonctionnement. De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Medical 1. This equipment is not suitable for use in the presence of flammable mixtures. 2. Connect to only IEC 60950-1 or IEC 60601-1 3rd Edition certified products and power sources. The end user is responsible for the overall medical system compliance in accordance with the requirements of IEC 60601-1 3rd edition. 3. Wipe with a dry cloth, no additional maintenance required. 4. No serviceable parts, the unit must be sent back to the manufacturer for repair. 5. No modifications are allowed without Dell approval. 第十二條 第十四條 NOTE: Expected Service Life 5 years. NOTE: For additional compliance information, pull down on the adhesive accordion sticker located on the side of the access point. This sticker may be folded back and resealed to it's original position once opened. Dell Networking W-AP205H Access Point Installation Guide Contacting Dell Web Site Support Main Website Contact Information Support Website Documentation Website dell.com dell.com/contactdell dell.com/support dell.com/support/manuals Copyright © 2015 Aruba Networks, Inc. Aruba Networks trademarks include , Aruba Networks®, Aruba Wireless Networks®, the registered Aruba the Mobile Edge Company logo, and Aruba Mobility Management System®. Dell™, the DELL™ logo, and PowerConnect™ are trademarks of Dell Inc. All rights reserved. Specifications in this manual are subject to change without notice. Originated in the USA. All other trademarks are the property of their respective owners. Open Source Code Certain Aruba products include Open Source software code developed by third parties, including software code subject to the GNU General Public License (GPL), GNU Lesser General Public License (LGPL), or other Open Source Licenses. The Open Source code used can be found at this site: http://www.arubanetworks.com/open_source Includes software from Litech Systems Design. The IF-MAP client library copyright 2011 Infoblox, Inc. All rights reserved. This product includes software developed by Lars Fenneberg, et al. Legal Notice The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate other vendors' VPN client devices constitutes complete acceptance of liability by that individual or corporation for this action and indemnifies, in full, Aruba Networks, Inc. from any and all legal actions that might be taken against it with respect to infringement of copyright on behalf of those vendors. www.dell.com Dell Networking W-AP205H Access Point | Installation Guide Part Number 0511784-01 | March 2015