Denon 589BA Owners Manual - Page 53

Getting Started Connections Setup Playback Remote Control Information Troubleshooting Specifications Troubleshooting ENGLISH If a problem should arise, first check the following: 1. Are the connections correct? 2. Is the set being operated as described in the owner's manual? 3. Are the other components operating properly? If this unit does not operate properly, check the items listed in the table below. Should the problem persist, there may be a malfunction. In this case, disconnect the power immediately and contact your store of purchase. GGeneralH Symptom Cause Countermeasure Set does not • External noise or interference is • Reset the microprocessor. operate properly. causing the set to malfunction. Power does not turn on, or turns off directly after it was turned on. • Connection of the power cord is • Check the insertion of the power faulty. cord plug. No sound is produced from speakers. • Connection with the input • Check the connections. devices or connection of the speaker cables is faulty. • Device you want to play and set • Select an appropriate input input source do not match. source. • Master volume is turned too • Adjust the master volume to an low. appropriate level. • Mute mode is set. • Cancel the mute mode. • Headphones are connected. • Disconnect the headphones. • No digital signals are being • Select an input source for which input. the digital input setting has been made. • The connectors to which the • Set the input mode. digital inputs are assigned and the settable input modes do not match. Display is off. • The Dimmer setting is set to • Set to something other than "OFF". "OFF". "DOLBY DIGITAL" • DVD player's digital audio output • Check the DVD player's audio indicator does not setting is not proper. output setting. For details, read appear on display. the DVD player's operating instructions. Power switches • The protection circuit will be • Please switch off power at once, off suddenly activated depending upon the and re-apply the power after while you are temperature rise in the internal the body temperature has fallen using the AVR- parts of the unit. sufficiently. 589, the power • Please re-install AVR-589 in a indicator will flash place having good ventilation. in red at intervals of approximately 2 seconds. Page 41 15 9 ~ 15 34 35 35 35 24 34 35 - 9 - Symptom Cause Countermeasure Power switches • Use speakers having impedance • Please use speakers which have off suddenly while less than that specified. the specified impedance. you are using • If speaker cable core wires touch • Unplug the power cord, then the AVR-589, the each other or the core wires after twisting the core wires power indicator become disconnected from their together tightly again, or effecting will flash red terminals, the protection circuit termination treatments etc, at intervals of will be activated in the event of please reconnect once again. approximately 0.5 core wires coming into contact seconds. with the AVR-589 rear panel. Even applying • The AVR-589 amplifier circuit has • Switch off the power and please power, the power failed. contact the DENON service display flashes adviser. red at intervals of approximately 0.5 seconds. GRemote Control UnitH Symptom Cause Countermeasure Set does not work • Batteries are worn. • Replace with new batteries. properly when • You are operating outside of the • Operate within the specified remote control specified range. range. unit operated. • Obstacle between main unit and • Remove the obstacle. remote control unit. • The batteries are not inserted in • Insert the batteries in the the proper direction, as indicated proper direction, following the by the polarity marks in the polarity marks in the battery battery compartment. compartment. • The set's remote control sensor • Move the set to a place in which is exposed to strong light (direct the remote control sensor will sunlight, inverter type fluorescent not be exposed to strong light. bulb light, etc.). • The remote ID of the main unit • Set "Remote ID" for the main and remote control unit do not unit to "1". match. • The SOURCE CONTROL switches • Set the SOURCE CONTROL are not set in the correct switches to the correct positions positions. according the operation you are applying. Page 9 9 - Page 3 3 3 3 3 26 36 ~ 38, 42 ~ 44 50