Denon AVR 2309CI Owners Manual - English - Page 54

Checking the SIRIUS Signal Strength, and Radio ID, Listening to Preset Channels, Presetting Radio

Get Denon AVR 2309CI - AV Receiver PDF manuals and user guides
UPC - 883795000611
View all Denon AVR 2309CI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Getting Started Connections Setup Playback Remote Control Multi-zone Information Troubleshooting Specifications ENGLISH Symbols used to indicate buttons in this manual Button located on both the main unit and the remote control unit BUTTON Button only on the main unit Button only on the remote control unit [BUTTON] TUNING ui SHIFT [Front] [OFF] [iPod] op [SAT TU1/2] SHIFT TUNING [CHANNEL + −] uiop [SOURCE CONTROL 1] [Rear] [iPod] [TUNING + −] [MODE] [MEMORY] [ENTER] [SOURCE CONTROL 2] [SAT TU 1/2] uiop [ENTER] Checking the SIRIUS Signal Strength and Radio ID 1 Either turn or press [SAT TU 1/2] to select "SIRIUS". 2 Press until "SIGNAL" appears on the display. The display will switch as shown below, depending on the reception conditions. Display EXCELLENT GOOD WEAK NO SIGNAL Status Signal strength is excellent Signal strength is good Signal strength is weak No signal 3 Adjust the position of the antenna until "SIGNAL: EXCELLENT" is shown on the display. 4 Press until the channel you want to check (example: "SR001") is displayed. 5 Press TUNING and select channel 0 (SR000). Channel No. and Sirius ID are alternately shown on the display. Presetting Radio Channels (Preset Memory) Your favorite broadcast channels can be preset so that you can tune them in easily. Up to 56 channels can be preset. 1 Tune in the broadcast channel you want to preset. 2 Press [MEMORY]. 3 Press SHIFT to select the block (A to G) in which the channel is to be preset. 4 Press or [CHANNEL + -] to select the preset number (1 to 8). 5 Press [MEMORY] again to complete the setting. To preset other channels, repeat steps 1 to 5. NOTE Preset channels are erased by overwriting them. SR000 SiriusID Sirius ID b Write your own SIRIUS ID for storage use. Sirius ID : Listening to Preset Channels 1 Press SIHFT to select the memory block (A to G). 2 The strength of both the SIRIUS and terrestrial signals can be checked Press or [CHANNEL + -] to select the desired preset channel (1 to 8). at menu "Input Setup" - "Antenna Aiming" (vpage 36). 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
µ±
ENGLISH
Getting Started
Connections
Setup
Remote Control
Multi-zone
Information
Troubleshooting
Specifications
Checking the SIRIUS Signal Strength
and Radio ID
1
Either turn
<SOURCE SELECT>
or press
[SAT TU 1/2]
to select “SIRIUS”.
2
Press
<STATUS>
until “SIGNAL” appears on the
display.
The display will switch as shown below, depending on the
reception conditions.
Display
Status
EXCELLENT
Signal strength is excellent
GOOD
Signal strength is good
WEAK
Signal strength is weak
NO SIGNAL
No signal
3
Adjust the position of the antenna until “SIGNAL:
EXCELLENT” is shown on the display.
4
Press
<STATUS>
until the channel you want to check
(example: “SR001”) is displayed.
5
Press
TUNING
and select channel 0 (SR000).
Channel No. and Sirius ID are alternately shown on the display.
SR000 SiriusID
************
b
Write your own SIRIUS ID for storage use.
Sirius ID :
Sirius ID
The strength of both the SIRIUS and terrestrial signals can be checked
at menu “Input Setup” – “Antenna Aiming” (
v
page 36).
op
<SOURCE SELECT>
<ON/STANDBY>
<STATUS>
TUNING
ui
SHIFT
uiop
[SOURCE
CONTROL 1]
TUNING
SHIFT
[iPod]
[OFF]
[SOURCE
CONTROL 2]
[CHANNEL + -]
[ENTER]
[SAT TU1/2]
uiop
[iPod]
[MODE]
[MEMORY]
[TUNING + -]
[ENTER]
[SAT TU 1/2]
[Front]
[Rear]
Button located on both the main unit and the remote control
unit
BUTTON
Button only on the main unit
<BUTTON>
Button only on the remote control unit
[BUTTON]
Symbols used to indicate buttons in this manual
Playback
Listening to Preset Channels
1
Press
SIHFT
to select the memory block (A to G).
2
Press
<PRESET>
or
[CHANNEL + –]
to select the
desired preset channel (1 to 8).
Presetting Radio Channels
(Preset Memory)
Your favorite broadcast channels can be preset so that you can
tune them in easily. Up to 56 channels can be preset.
1
Tune in the broadcast channel you want to preset.
2
Press
[MEMORY]
.
3
Press
SHIFT
to select the block (A to G) in which the
channel is to be preset.
4
Press
<PRESET>
or
[CHANNEL + –]
to select the preset
number (1 to 8).
5
Press
[MEMORY]
again to complete the setting.
To preset other channels, repeat steps 1 to 5.
NOTE
Preset channels are erased by overwriting them.