Denon AVR 688 Owners Manual - English - Page 42

Playback - receivers

Get Denon AVR 688 - AV Receiver PDF manuals and user guides
UPC - 081757507851
View all Denon AVR 688 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting ENGLISH [Front] [1] [6], [7] [8], [9] uiop [MODE SELECTOR 1] [Rear] [MODE] uiop STATUS ui op [CHANNEL +/-] [2] [ENTER] STATUS [MODE SELECTOR 2] [iPod] Searching Categories 1 Press o p. CAT: Rock Channel category 2 Use o p to select the category, then use ui to select the desired station. Basic Operation 1 Make the necessary preparations. qSet the iPod in the DENON Control Dock for iPod. (vSee the Control Dock for iPod's operating instructions.) wAssign the Control Dock for iPod's input. "System Setup" - "Input Setup" - "iPod Assign" (vpage 26) • "LOADING" is displayed while stations or data are being received. • "UPDATING" is displayed while the encording code is being updated. • "XM - - -" is displayed if the selected channel cannot be used. 2 Either turn or press [iPod] to select the input source assigned in step 1-w above. Remote iPod b If the displays above are not displayed, the iPod may not be properly connected. Try connecting again. iPod® Playback The music on an iPod can be played by using the Control Dock for iPod (ASD-1R, sold separately). The operation can also be performed using the buttons on the remote control unit. 3 Set [MODE SELECTOR 1] to "AUDIO" and [MODE SELECTOR 2] to "iPod/NETWORK". (vpage 43 "Remote Control Unit Operations") iPod is a trademark of Apple Inc., registered in the U.S. and other countries. b The iPod may only be used to copy or play contents that are not copyrighted or contents for which copying or playback is legally permitted for your private use as an individual. Be sure to comply with applicable copyright legislation. • With the default settings, the iPod can be used connected to the VCR (iPod) connector. • Use the RESTORER mode to expand the low and high frequency components of compressed audio files and achieve a richer sound. The default setting is "Mode3" (vpage 33). • Press and set the AVR-688's power to the standby mode before disconnecting the iPod. Also switch the input source to one to which "iPod Assign" is not assigned before disconnecting the iPod. [ENTER] About the button names in these explanations < > : Buttons on the main unit [ ] : Buttons on the remote control unit Button name only: Buttons on the main unit and remote control unit 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
³¹
Getting Started
Connections
Setup
Playback
Remote Control
Multi-Zone
Information
Troubleshooting
ENGLISH
Getting Started
Connections
Setup
Playback
Remote Control
Multi-Zone
Information
Troubleshooting
iPod
®
Playback
The music on an iPod can be played by using the Control Dock for
iPod (ASD-1R, sold separately).
The operation can also be performed using the buttons on the
remote control unit.
iPod is a trademark of Apple Inc., registered in the U.S.
and other countries.
b
The iPod may only be used to copy or play contents that are not
copyrighted or contents for which copying or playback is legally
permitted for your private use as an individual. Be sure to comply
with applicable copyright legislation.
1
Make the necessary preparations.
q
Set the iPod in the DENON Control Dock for iPod.
(
v
See the Control Dock for iPod’s operating instructions.)
w
Assign the Control Dock for iPod’s input.
“System Setup” –
”Input Setup”
–
”iPod Assign”
(
v
page 26)
2
Either turn
<SOURCE SELECT>
or press
[iPod]
to
select the input source assigned in step 1-
w
above.
Remote iPod
b
If the displays above are not displayed, the iPod may not be
properly connected. Try connecting again.
3
Set
[MODE SELECTOR 1]
to “AUDIO” and
[MODE
SELECTOR 2]
to “iPod/NETWORK”.
(
v
page 43 “Remote Control Unit Operations”)
Basic Operation
• With the default settings, the iPod can be used connected to the VCR
(iPod) connector.
• Use the RESTORER mode to expand the low and high frequency
components of compressed audio files and achieve a richer sound.
The default setting is “Mode3” (
v
page 33).
• Press
<ON/STANDBY>
and set the AVR-688’s power to the standby
mode before disconnecting the iPod. Also switch the input source to
one to which “iPod Assign” is not assigned before disconnecting the
iPod.
<SOURCE SELECT>
STATUS
op
ui
<ON/STANDBY>
About the button names in these explanations
<
>
: Buttons on the main unit
[
]
: Buttons on the remote control unit
Button name only:
Buttons on the main unit and remote control unit
uiop
[
1
]
[
6
], [
7
]
[
8
], [
9
]
[
2
]
[ENTER]
STATUS
[MODE
SELECTOR 1]
[MODE
SELECTOR 2]
[CHANNEL +/–]
uiop
[ENTER]
[iPod]
[MODE]
[Front]
[Rear]
Searching Categories
1
Press
o
p
.
CAT:
Rock
2
Use
o
p
to select the category, then use
ui
to select
the desired station.
Channel category
• “LOADING” is displayed while stations or data are being received.
• “UPDATING” is displayed while the encording code is being
updated.
• “XM – – –” is displayed if the selected channel cannot be used.