Denon AVR 988 Owners Manual - English - Page 49

Searching Categories, Checking the XM Signal Strength and, Radio ID

Get Denon AVR 988 - AV Receiver PDF manuals and user guides
UPC - 081757507684
View all Denon AVR 988 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting Checking the XM Signal Strength and Radio ID 1 Either turn or press [SAT TU] to select "XM". 2 Press until "SIGNAL" appears on the display. The display will switch as shown below, depending on the reception conditions. Display GOOD MARGINAL WEAK NO Status Signal strength is good Signal strength is marginal Signal strength is weak No signal Searching Categories 1 Press o p. Channel category 2 Use o p to select the category, then use ui to select the desired station. 3 Adjust the position of the antenna until "SIGNAL: GOOD" is shown on the display. 4 Press until the station you want to check (example: "XM001") is displayed. 5 Press [TUNING] and select channel 0 (XM000). The radio ID is shown on the display. Radio ID The strength of both the XM satellite and terrestrial signals can be checked at menu "Input Setup" - "Antenna Aiming" (vpage 36). 46

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Searching Categories
1
Press
o
p
.
2
Use
o
p
to select the category, then use
ui
to select
the desired station.
Channel category
Checking the XM Signal Strength and
Radio ID
1
Either turn
<SOURCE SELECT>
or press
[SAT TU]
to
select “XM”.
2
Press
<STATUS>
until “SIGNAL” appears on the
display.
The display will switch as shown below, depending on the
reception conditions.
Display
Status
GOOD
Signal strength is good
MARGINAL
Signal strength is marginal
WEAK
Signal strength is weak
NO
No signal
3
Adjust the position of the antenna until “SIGNAL:
GOOD” is shown on the display.
4
Press
<STATUS>
until the station you want to check
(example: “XM001”) is displayed.
5
Press
[TUNING]
and select channel 0 (XM000).
The radio ID is shown on the display.
The strength of both the XM satellite and terrestrial signals can be
checked at menu “Input Setup” – “Antenna Aiming” (
v
page 36).
Radio ID
´¶
Getting Started
Connections
Setup
Playback
Remote Control
Multi-Zone
Information
Troubleshooting