Denon DCM-5000 Owners Manual - Page 8

Installation

Page 8 highlights

ENGLISH 6 INSTALLATION Removing the Shipping Screws The internal mechanisms are locked in place with shipping screws to protect them from shocks and vibrations. Be sure to remove the shipping screws (three) before using the player. 1 Turn the three shipping screws on section A of the rear panel counterclockwise and remove them. 2 Fasten the removed shipping screws in the holes in section B. * The shipping screws and rubber washers will be needed when shipping the player in the future, so be sure to fasten them to the holes in section B so as not to lose them. [When moving the player] When shipping the player, be sure to protect the internal mechanisms from shocks and vibrations using the procedure described below. 1 Remove all the CDs from the disc rack following the procedure described under "Loading CDs" (page 9). 2 Close the front cover. • "NO DISC" appears on the display once all the CDs have been removed. 3 Press the power operation switch (¢ ON/STANDBY) to turn the power off. 4 Press the power operation switch (¢ ON/STANDBY) while pressing in the DOOR OPEN button to turn the power on. Do not release the DOOR OPEN button until "FIX SCREW" appears on the display. 5 Once "FIX SCREW" appears on the display, remove the three shipping screws from section B of the rear panel, put them in the holes in section A, then tighten them to lock the internal mechanism in place. 6 Press the power operation switch (¢ ON/STANDBY) to turn the power off. MODE Switch Settings There are mode switches on the rear panel for setting the operation mode. Set the mode switches according to the usage purpose. 0 To control with a personal computer. SW 1 1 To use in the stand alone mode. 0 SW 2 1 SW 3 0 These do not affect the DCM-5000's operation 1 mode. 0 SW 4 1 * When SW 1 is set to "0", the only operations possible on the DCM5000 are turning the power on and off and opening the door. Upon shipment from the factory, SW 1 is set to "1" and all the other switches are set to "0". 8 Section A Section B w q Shipping screws Section A Section B t Shipping screws 1234 1234 1 2 1 ANALOG OUT 2 1 2 R L DAISY CHAIN IN DIGITAL COAX IN DIGITAL COAX OUT VIDEO OUT REMOTE CONTROL IN DAISY CHAIN CONTROL MODE SWITCH 10 EXTERNAL CONTROL ¢ RS232C £ RS422A ATTENTION 10 ATTENTION

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42

ENGLISH
8
The internal mechanisms are locked in place with shipping
screws to protect them from shocks and vibrations.
Be sure to
remove the shipping screws (three) before using the player.
1
Turn the three shipping screws on section A of the rear
panel counterclockwise and remove them.
1
Remove all the CDs from the disc rack following the
procedure described under “Loading CDs” (page 9).
4
Press the power operation switch (
¢
ON/STANDBY) while
pressing in the DOOR OPEN button to turn the power on.
Do not release the DOOR OPEN button until “
FIX
SCREW
” appears on the display.
3
Press the power operation switch (
¢
ON/STANDBY) to
turn the power off.
6
Press the power operation switch (
¢
ON/STANDBY) to
turn the power off.
5
Once “
FIX SCREW
” appears on the display, remove the
three shipping screws from section B of the rear panel, put
them in the holes in section A, then tighten them to lock
the internal mechanism in place.
2
2
Fasten the removed shipping screws in the holes in section
B.
* The shipping screws and rubber washers will be
needed when shipping the player in the future, so be
sure to fasten them to the holes in section B so as
not to lose them.
Shipping screws
There are mode switches on the rear panel for setting the
operation mode.
Set the mode switches according to the usage
purpose.
To control with a personal computer.
To use in the stand alone mode.
These do not affect the DCM-5000’s operation
mode.
SW 1
SW 2
SW 3
SW 4
0
1
0
1
0
1
0
1
q
1
DIGITAL COAX IN
DAISY CHAIN IN
DIGITAL COAX OUT
VIDEO OUT
REMOTE CONTROL IN
2
1
2
1
2
ANALOG OUT
R
L
CONTROL
DAISY CHAIN
CONTROL
EXTERNAL
MODE SWITCH
¢
RS232C
£
RS422A
1
0
ATTENTION
ATTENTION
1
0
1
2
3
4
*
When SW 1 is set to “
0
”, the only operations possible on the DCM-
5000 are turning the power on and off and opening the door.
Upon shipment from the factory, SW 1 is set to “
1
” and all the other
switches are set to “
0
”.
[When moving the player]
When shipping the player, be sure to protect the internal
mechanisms from shocks and vibrations using the procedure
described below.
Close the front cover.
•“
NO DISC
” appears on the display once all the CDs
have been removed.
Section
A
INSTALLATION
6
Removing the Shipping Screws
MODE Switch Settings
w
Section
B
Section
A
Section
B
Shipping screws
t