Dewalt D51321 Instruction Manual - Page 6

614989-00, D51321 3/19/04 5:45 PM Page 6 Fig. 10 Compressor will be sufficient for tools at all production rates. Le compresseur peut actionner tout outil, quel que soit le taux de production. El compresor será suficiente para las herramientas a todo índice de producción. Compressor will be sufficient at slow or moderate production rates, but may have difficulty at very rapid rates. Le compresseur peut actionner des outils à des taux de production faibles ou modérés, mais peut avoir de la difficulté à des taux très élevés. El compresor será suficiente a índices de producción lentos o moderados pero tendrá dificultad con índices demasiado rápidos. Compressor will be adequate only when tools are utilized at slow production rates. (punch-out or occasional use) Le compresseur ne sera vraiment efficace que lorsque les outils sont utilisés à de faibles taux de production (p. ex., lors de travaux rapides ou occasionnels). El compresor será adecuado sólo cuando las herramientas sean utilizadas a índices de producción lentos (perforación o uso ocasional). Not Recommended Taux non recommandés No se recomienda Portable Handcarry 3.2 - 4 CFM Petit outil portatif 5,4 - 6,8 CMM (3,2 - 4 CFM) Portátil 5,4 - 6,8 CMM (3,2 - 4 CFM) 5.5 HP Gas 2 HP Elec. 8 - 9 CFM Outil à gaz (5,5 hp) Outil électrique (2 hp) 13,6 - 15,3 CMM (8 - 9 CFM) 5,5 HP Gas 2 HP Elec. 13,6 - 15,3 CMM (8 - 9 CFM) 8 HP Gas 14 - 16 CFM Outil à gaz (8 hp) 23,8 - 27,2 CMM (14 - 16 CFM) 8 HP Gas 23,8 - 27,2 CMM (14 - 16 CFM) Industrial 23+ CFM Outil industriel 39,1+ CMM (23+ CFM) Industrial 39,1+ CMM (23+ CFM) 1 NAIL SPECIFICATIONS D51321 COIL ROOFING NAILER CARACTÉRISTIQUES DES CLOUS D51321 CLOUEUSE À BOBINE POUR TOITURES ESPECIFICACIONES DE LOS CLAVOS D51321 CLAVADORA PARA TECHADO EN ROLLO Nail Lengths Longueur .75'' - 1.75'' 20 - 40 mm (0,75 - 1,75 po.) Largo de clavos 20 - 40 mm (0,75 - 1,75 pulg.) Shank Diameters .120 Diamètre de tige 3 mm (0,120 po.) Diámetro del vástago 3 mm (0,120 pulg.) Nail Coil Angle 15˚ Angle de la bobine 15° Ángulo del rollo de clavos 15˚ 2 TOOL SPECIFICATIONS D51321 COIL ROOFING NAILER CARACTÉRISTIQUES DE L'OUTIL 3 D51321 CLOUEUSE À BOBINE POUR TOITURES ESPECIFICACIONES DE LA HERRAMIENTA D51321 CLAVADORA PARA TECHADO EN ROLLO Height / Hauteur / Altura 11.4'' (289,6 mm) 4 Width / Largeur / Ancho 4.6" (118,1 mm) Length / Longueur / Largo 10.6'' (269,7 mm) Weight / Poids / Peso 4.90 lbs. (2,22 kg) 5 Recommended Operating Pressure 70 - 120 psig (4.9 - 8.3 bar, 5 to 8.5 kg/cm2) Pression d'utilisation recommandée de 5 à 8,5 kg/cm2 (70 à 120 lb/po2 ou 4,9 à 8,3 bar) Presión de operación recomendada 70 - 120 psi (4,9 - 8,3 bar, 5 a 8,5 kg/cm2) Air Consumption per 100 cycles 4.15 scfm @ 100 psi 6 Consommation d'air par 100 cycles 4,15 scfm à 100 psi (0,12 scmm a 6,9 bar) Consumo de aire por cada 100 ciclos 4,15 scfm a 100 psi (0,12 scmm a 6,9 bar) Loading capacity Up to 120 nails Capacité de charge Jusqu'à 120 clous 7 Capacidad de carga Hasta 120 clavos NUMBER OF TOOLS CONNECTED TO COMPRESSOR NOMBRE D'OUTILS RACCORDÉS AU COMPRESSEUR NÚMERO DE HERRAMIENTAS CONECTADAS AL COMPRESOR 8+ Troubleshooting Guide MANY COMMON PROBLEMS CAN BE SOLVED EASILY BY UTILIZING THE CHART BELOW. FOR MORE SERIOUS OR PERSISTENT PROBLEMS, CONTACT A DEWALT SERVICE CENTER OR CALL 1-(800)-4-DEWALT. DISCONNECT AIR FROM TOOL BEFORE ALL REPAIRS Trigger valve housing leaks O-ring or valve stem failure Replace valve using: Trigger Valve Kit: Cat. # D510005 Top cap leaks air Loose cap screws Tighten cap screws using appropriate Allen wrench Damaged or worn gasket or O-ring Replace gasket/O-rings using: O-ring Repair Kit, Cat. # D513211 Exhaust leaks Main seal or O-ring damaged, debris in tool. Replace gasket/O-rings using: O-ring Repair Kit, Cat. # D513211 Air leaks around nose when tool is at rest. (Driver blade in up position) Damaged or worn O-rings Replace gasket/O-rings using: O-ring Repair Kit, Cat. # D513211 Air leaks around nose when tool is in actuated position. (Driver blade in down position) Damaged or worn bumper Replace bumper using: Bumper Kit, Cat. # D513213 Tool does not cycle in cold weather Tool not receiving air Check air supply Valve may be frozen Warm up tool Damaged or worn O-rings Replace gasket/O-rings using: O-ring Repair Kit, Cat. # D513211 Broken or damaged driver blade Replace Driver Blade Kit: Cat. # D513212 Lack of power; sluggish Low air pressure Check air supply Lack of lubrication Lubricate tool using approved pneumatic tool oil. Damaged or worn O-rings Replace gasket/O-rings using: O-ring Repair Kit, Cat # D513211 Exhaust port blocked or clogged Disconnect air, remove exhaust plate from top of tool, clean port Skipping nails; intermittent feed Air restricted Check air supply and couplers Lack of lubrication Lubricate tool using approved pneumatic tool oil Nose piece screws loose Tighten nosepiece screws using appropriate allen wrench Wrong size/angle fasteners Use only recommended fasteners Dirty canister Clean canister track and nosepiece Worn canister Replace canister Broken or damaged driver blade Replace Driver Blade Kit; Cat. # D513212 Trigger valve O-ring worn or damaged Replace valve using: Trigger Valve Kit; Cat. # D510005 Worn piston O-ring Replace Piston O-Ring using: O-Ring Repair Kit, Cat.# D513211 Worn or damaged check pawl and/or feed pawl Replace check pawl and/or feed pawl Canister loose Check that canister latch is holding firmly Nail platform at incorrect setting Set nail platform to proper nail setting Feed piston O-ring worn or damaged Replace feed piston O-ring using: O-Ring Repair Kit, Cat. # D513211 Fasteners jam in tool Driver channel in nose piece worn Replace nosepiece Wrong size/ angle fasteners Use only recommended fasteners Canister loose Check that canister screws are holding firmly Worn driver blade Replace Driver Blade Kit; Cat # D513212 Nose piece screws loose Tighten nosepiece screws using appropriate Allen wrench Nails not feeding properly Ensure nails are feeding properly into nose.