Dewalt DCD991P2 Instruction Manual - Page 17

MAINTENANCE, Cleaning, Accessories, Repairs

Get Dewalt DCD991P2 PDF manuals and user guides View all Dewalt DCD991P2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

English 4. When drilling deep holes, if the hammer speed starts to drop off, pull the bit partially out of the hole with tool still running to help clear debris from the hole. NOTE: A smooth, even flow of dust from the hole indicates proper drilling rate. MAINTENANCE WARNING: To reduce the risk of serious personal injury, turn tool off and remove the battery pack before making any adjustments or removing/installing attachments or accessories. An accidental start-up can cause injury. Cleaning WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week. To minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when performing this. WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. CHARGER CLEANING INSTRUCTIONS WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning. Dirt and grease may be removed from the exterior of the charger using a cloth or soft non-metallic brush. Do not use water or any cleaning solutions. Accessories WARNING: Since accessories, other than those offered by DeWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only DeWALT recommended accessories should be used with this product. Recommended accessories for use with your tool are available at extra cost from your local service center. If you need any assistance in locating any accessory, please contact DeWALT Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286, call 1-800-4-DeWALT (1-800-433-9258) or visit our website: www.dewalt.com. MAXIMUM RECOMMENDED CAPACITIES DCD991 DCD996 WOOD Auger 1-1/4" (32 mm) 1-1/4" (32 mm) Paddle 1-1/2" (38 mm) 1-1/2" (38 mm) Twist 1/2" (13 mm) 1/2" (13 mm) Self-feed 2-9/16" (65 mm) 2-9/16" (65 mm) Hole saw 4" (100 mm) 4" (100 mm) METAL Twist 1/2" (13 mm) 1/2" (13 mm) Hole saw 1-3/8" (35 mm) 1-3/8" (35 mm) MASONRY Carbide - 1/2" (13 mm) Repairs The charger and battery pack are not serviceable. There are no serviceable parts inside the charger or battery pack. To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustments should be performed by a DeWALT factory service 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
15
English
4. When drilling deep holes, if the hammer speed starts to drop off,
pull the bit partially out of the hole with tool still running to help
clear debris from the hole.
NOTE:
A smooth, even flow of dust from the hole indicates proper
drilling rate.
MAINTENANCE
WARNING: To reduce the risk of serious personal injury,
turn tool off and remove the battery pack before making any
adjustments or removing/installing attachments or accessories.
An accidental start-up can cause injury.
Cleaning
WARNING:
Blow dirt and dust out of all air vents with clean, dry air
at least once a week. To minimize the risk of eye injury, always wear
ANSI Z87.1 approved eye protection when performing this.
WARNING:
Never use solvents or other harsh chemicals for cleaning
the non-metallic parts of the tool. These chemicals may weaken the
plastic materials used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the tool; never
immerse any part of the tool into a liquid.
CHARGER CLEANING INSTRUCTIONS
WARNING:
Shock hazard. Disconnect the charger from the AC
outlet before cleaning. Dirt and grease may be removed from the
exterior of the charger using a cloth or soft non-metallic brush. Do not
use water or any cleaning solutions.
Accessories
WARNING:
Since accessories, other than those offered by D
E
WALT,
have not been tested with this product, use of such accessories with
this tool could be hazardous. To reduce the risk of injury, only D
E
WALT
recommended accessories should be used with this product.
Recommended accessories for use with your tool are available at
extra cost from your local service center. If you need any assistance
in locating any accessory, please contact D
E
WALT Industrial Tool Co.,
701 East Joppa Road, Towson, MD 21286, call 1-800-4-D
E
WALT
(1-800-433-9258) or visit our website: www.dewalt.com.
MAXIMUM RECOMMENDED CAPACITIES
DCD991
DCD996
WOOD
Auger
1-1/4" (32 mm)
1-1/4" (32 mm)
Paddle
1-1/2" (38 mm)
1-1/2" (38 mm)
Twist
1/2" (13 mm)
1/2" (13 mm)
Self-feed
2-9/16" (65 mm)
2-9/16" (65 mm)
Hole saw
4" (100 mm)
4" (100 mm)
METAL
Twist
1/2" (13 mm)
1/2" (13 mm)
Hole saw
1-3/8" (35 mm)
1-3/8" (35 mm)
MASONRY
Carbide
–
1/2" (13 mm)
Repairs
The charger and battery pack are not serviceable. There are no
serviceable parts inside the charger or battery pack.
To assure product SAFETY and RELIABILITY, repairs, maintenance
and adjustments should be performed by a D
E
WALT factory service