Dewalt DWE4559CN Instruction Manual - Page 13

Mounting Guard, Sanding Flap Discs

Get Dewalt DWE4559CN PDF manuals and user guides View all Dewalt DWE4559CN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

English Type 11 flaring cup wheel backing flange N197992 Type 1 flange set D284932 7" Type 1 guard D284931 Grinding backing flange 54339-00 Clamp nut 22191-00 Wheel wrench 61820-01 Soft mount spindle protector 445928-01 WARNING: Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other accessories running over their rated accessory speed may fly apart and cause injury. Threaded accessories must have a 5/8"-11 hub. Every unthreaded accessory must have a 7/8" (22.2 mm) arbor hole. If it does not, it may have been designed for a circular saw. Use only the accessories shown on pages 11-13 of this manual. Accessory ratings must always be above tool speed as shown on tool nameplate. Mounting Guard Sanding Flap Discs soft mount 445928-01 soft mount 445928-01 Type 27 guard D284937 7" D284939 9" hubbed sanding flap disc Type 27 guard D284937 7" D284939 9" backing flange 54339-00 MOUNTING AND REMOVING GUARD (FIG. 6, 7) WARNING: Guards must be used with all grinding wheels, cutting wheels, sanding flap discs, wire brushes, and wire wheels. Guard modification that results in reduced coverage of the accessory could result in severe personal injury. The tool may be used without a guard only when sanding with conventional sanding discs. A Type 27 guard (intended for use with depressed center grinding wheels [Type 27 and Type 29], sanding flap discs, wire wheels and wire cup brushes) is available at extra cost from your local dealer or authorized service center. Grinding and cutting with wheels other than Type 27 and 29 require different accessory guards not included with tool. A Type 1 guard is provided for use with the Type 1 wheel. Mounting instructions for accessory guards are shown below and are also included in the accessory package. non-hubbed sanding flap disc clamp nut 22191-00 NOTE: Wheel size must match guard size; i.e., a new 7" wheel may not be used with a 9" guard. The bottom surface of wheel must be inside the bend of the guard lip. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Type 11 flaring cup wheel backing flange
N197992
Type 1 flange set
D284932
7" Type 1 guard
D284931
Grinding backing flange
54339-00
Clamp nut
22191-00
Wheel wrench
61820-01
Soft mount spindle protector
445928-01
WARNING:
Accessories must be rated for at least the speed
recommended on the tool warning label. Wheels and other
accessories running over their rated accessory speed may fly apart
and cause injury. Threaded accessories must have a 5/8"
–
11 hub.
Every unthreaded accessory must have a 7/8" (22.2 mm) arbor
hole. If it does not, it may have been designed for a circular saw.
Use only the accessories shown on pages 11–13 of this manual.
Accessory ratings must always be above tool speed as shown on
tool nameplate.
Mounting Guard
MOUNTING AND REMOVING GUARD (FIG. 6, 7)
WARNING: Guards must be used with all grinding wheels,
cutting wheels, sanding flap discs, wire brushes, and wire
wheels. Guard modification that results in reduced coverage
of the accessory could result in severe personal injury.
The tool
may be used without a guard only when sanding with conventional
sanding discs. A Type 27 guard (intended for use with depressed
center grinding wheels [Type 27 and Type 29], sanding flap discs, wire
wheels and wire cup brushes) is available at extra cost from your local
dealer or authorized service center. Grinding and cutting with wheels
other than Type 27 and 29 require different accessory guards not
included with tool. A Type 1 guard is provided for use with the Type 1
wheel. Mounting instructions for accessory guards are shown below
and are also included in the accessory package.
NOTE:
Wheel size must match guard size; i.e., a new 7" wheel may
not be used with a 9" guard. The bottom surface of wheel must be
inside the bend of the guard lip.
soft mount
445928-01
Type 27 guard
D284937 7"
D284939 9"
backing flange
54339-00
non-hubbed sanding
flap disc
clamp nut
22191-00
Sanding Flap Discs
soft mount
445928-01
Type 27 guard
D284937 7"
D284939 9"
hubbed sanding
flap disc
English
11