Dirt Devil M0880DV Revision 1 (5/2004) - Page 2

ChargingIStorage Base, Dirt Cup Release Button, Side Air Vents, Crevice Tool Release Button, Handle - filters

Get Dirt Devil M0880DV PDF manuals and user guides View all Dirt Devil M0880DV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

I 1. ChargingIStorage Base 2. Side Air Vents 3. Handle 4. Power Switch 5. Charging Light I 6. Dirt Cup Release Button 7. Crevice Tool Release Button 8. Crevice Tool 9. Dirt Cup TOOL REQUIRED: SCREWDRIVER AND DRILL A. CHARGINGISTORAGE BASE Designed to sit in the charging base on a flat surface (Diagram 1) or mount vertically (Diagram 2). For tidy storage, wrap excess cord on the back of the charging base and exit at either side or out the bottom. TO WALL MOUNT: 1. Place charging base against the mounting surface. Mark the centers of the holes. 2. Move base, then drill a 3/16" hole through the center of the marks. 3. Push plastic wall anchor into the drilled hole. 4. Be sure marked location is correct before drilling the second hole (adjust if necessary). Drill second hole and install other wall anchor. 5. Match up holes in storage base to wall anchors and insert screws. Be sure surface. cord exits from one of the cord slots on the storage base. 6. Tlghten the screws to hold the base flush to the mounting surface. B. UNlT STORAGE 1. Hold the unit by the handle and push down firmly onto the charging base. 2. Be sure the red charging light is on. C. CHARGING NOTE: Use only the charger supplied by the manufacturer to recharge. IMPORTANT: BEFORE FIRST USE, CHARGE YOUR UNlT FOR AT LEAST 24 HOURS. Power switch must be in the OFF position. Keep the charger plugged into a standard outlet at all times. It is normal for Designed to mount vertical- the charger to become warm to the touch when charging. ly on the wall. If the operating time gets shorter after repeated use, let the unit run until it stops running. Recharge for 24 hours and repeat monthly for best results. I U ust: srlae the power sw~tchto the ON position. TO TURN UNlT OFF: Slide the power switch to the OFF position. Empty and clean the unit and filter after each use or after large pickups when the unit becomes full. TO USE TO STORE . . Press the crevice tool release button. Flip crevice tool down to line up with nozzle then press up until secure in place. To store crevice tool: Pull down until loose. Flip crevice tool up towards unit and press until you feel it lock into place. REMOVE DIRT CUP: Depress the dirt cup release button and pull nozzle away from unit. Hold nozzle over a wastebasket. Grasp filter and gently pull out. Shake excess dirt and debris out of dirt CUD. For best results, tap filter against wastebasket to remove remaining dirt.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
I
I
1.
ChargingIStorage Base
6.
Dirt Cup Release Button
2.
Side Air Vents
7.
Crevice Tool Release Button
3.
Handle
8.
Crevice Tool
4.
Power Switch
9.
Dirt
Cup
5.
Charging Light
TOOL REQUIRED: SCREWDRIVER
AND
DRILL
A.
CHARGINGISTORAGE BASE
Designed to sit in the charging base on a flat surface (Diagram 1) or mount
vertically (Diagram 2).
For tidy storage, wrap excess cord on the back of the charging base and exit
at either side or out the bottom.
TO WALL MOUNT:
1.
Place charging base against the mounting surface. Mark the centers of the holes.
2.
Move base, then drill a 3/16" hole through the center of the marks.
3.
Push plastic wall anchor into the drilled hole.
4.
Be sure marked location is correct before drilling the second hole (adjust if
necessary). Drill second hole and install other wall anchor.
surface.
5.
Match up holes in storage base to wall anchors and insert screws. Be sure
cord exits from one of the cord slots on the storage base.
6.
Tlghten the screws to hold the base flush to the mounting surface.
B.
UNlT STORAGE
1.
Hold the unit by the handle and push down firmly onto the charging base.
2.
Be sure the red charging light is on.
C.
CHARGING
NOTE:
Use only the charger supplied
by
the manufacturer
to
recharge.
IMPORTANT:
BEFORE FIRST USE, CHARGE YOUR UNlT FOR AT LEAST 24 HOURS.
Power switch must be in the OFF position.
Keep the charger plugged into a standard outlet at all times. It is normal for
Designed to mount vertical-
the charger to become warm to the touch when charging.
ly on the wall.
If the operating time gets shorter after repeated use, let the unit run until it
stops running. Recharge for 24 hours and repeat monthly for best results.
IU
ust:
srlae the power sw~tch
to the
ON
position.
TO TURN UNlT OFF:
Slide the power switch to the OFF position.
Empty and clean the unit and filter after each use or after large pickups when the unit becomes full.
TO USE
.
.
TO STORE
Press the crevice tool
Flip crevice tool down to line
To store crevice tool: Pull down until loose.
release button.
up with nozzle then press up
Flip crevice tool up towards unit and press
until secure in place.
until you feel
it
lock into place.
REMOVE DIRT CUP:
Hold nozzle over a wastebas-
Shake excess dirt and debris out of dirt
CUD.
Depress the dirt cup release
ket. Grasp filter and gently
For best results, tap filter against wastebasket
button and pull nozzle away
pull out.
to remove remaining dirt.
from unit.