Edimax ES-5500G Quick Install Guide - Page 1
Edimax ES-5500G Manual
View all Edimax ES-5500G manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
NEIVIO0.1010 PEOPLE TOSETMER 5 / 8 Ports Desktop Gigabit Ethernet Switches ES-5500G / ES-5800G Quick Installation Guide Version 1.0 / September, 2009 m7!iP!w5. Copyright0by Edimax Technology Co, LTD. all rights reserved. No part Syria pubtication rary be reproduced, transmitted, honseribed, stored e a retrieval system, or translated into any language a computer temp.'e. In any born Or by any means, etedoonk, mxbaNpl, meta., oat., cheml., mama or Mena, without the Mandato permission of Ns company This company makes no representations or warrantee, either expressed crimpled, with resod° the co.nd hereof and specifically disclaims any warmtim, marchturlability a fitness for any particular purpose. Any software deealbed in this manual is sold or licensed 'as is . Should the programs prove defective folkwing their purchase, the buyer (end not aria company. its distributor, or its dealer) assumes the entire cost of all necessary servicing repak and any inddental consequential damages resubng from any detest in the solbsere. Further, this company reserves the right to reds this publication and to make changes from time to time in the conted hereof withan obligation to notify any pawn Sauce revision or enemas. The product you have purehased and the setup screen may appear slightly different from those shown in this Manual. The software and specifications are subject to change without not.. Please visit our web site wormed...am for the update. All dghb reserved including all brand and product names me.ned in the man. ere.demerks anaor registered trademarks of their respective holders. Federal Communication Commission interference Statement This equipment . been tested and found to comply wail the limits for a Cress B dlpal dm., pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable nation against hannful Interference Ina residential Installation. This equipment generates, we, and can radiate radio frequency energy and, if not in.!ted and used in awardersce nth the .8..08, may cause harmful interference to ratio communication. However, there is no guarantee that interference will not occur in a particular installation. If the equipment doe cause harmful interference b radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the i.rfanince by one or more of ma following measures: 1. Reorient or .ssate the meek', antenna. 2. Increase the eeparatlon between the eaten.. and receiver. S. Connect the equipment into an cutlet co a deed different from that toyMich the receiver is connected. S. Consult the dealer °ran operienced radio technician for help. FCC Caution This device end fie antenna must red be co-located or operating In conjunction WM any other a.nna or tranamitter.T. device complies with Pad 15 of the FCC Rule. Ops.on is subject to the following boo conditions: (1) this device may flatware harmful Interference, and (2) this device m. meant any 'Madelyn. received including interferers:4,MR may care undeei. opera.. My changes a. modifications . expressly approved by the party responsible for compliance could void the e.ority to operate equipment. CE Mink Warning. This is a Cleo A pmduct Ina domestic environment. the pmduct may cause radio int., in ankh nee the user may be required to take adequate measures. Thank you for purchasing Edimax gigabit sedan. This high cost-efficiency swath complies with 10/100/1000-Base-TX standards is the best Stoic* for Small office / Flame office sers. The ES-5500G/ES-5800G supports dynamic detection of cable length and dynamic adjustment of power required for the detected cable imp for power seines . The switch also can detect link status for each port:. When the port is Idle, the ES-55(10G/ES-5800G wel reduce power usage for the pod. Easy Metall procedures allows any computer users to setup a network environment In very short time . Product Package The package contains the following components: • One Gigabit Switch • Quick installation Guide • 5V 1A (ES.550DG)/ 12V 1A (ES-5800G) • Accessories kit • amitem is missing or damaged, please contact your local re-sellers for orrice. Feature • Complies with the IEEE 802.3, IEEE 802.3u and IEEE 802.3ab standards. • Smart Green Ethemet technology to reduce power consumption 35%-50%. • Provides Store and Forward architecture, full wire speed fltedng and forwarding rates. • Supports Auto-MDINDI-X. full/hall duplex modes and auto.negotiation. • Supports flow control: back pressure for half-duplex, IEEE 802.3x for full-cluplex mode. • Supports Jumbo Frame in all speeds mode (10/100/1000Mbps). • Automatic source address learning and aging, °dens. front-panel diagnostic LEDs. Front Panels Connector. WI% ES-5500C I 1 EB-SBOOG 2 3 Fast Ethernet Switch LED Panel PWR (Power) LNK/ACT (Link/Activity) Green Green Lit Off Lit Flash Off The switch is powered on The switch b powered on Avalid link is established Data packets received No link is established 1. Operating Environment This switching hub must be installed and operated within the limits of specified operating temperature 0, 40°C (32°-104°F) and humidity 10% - 90% (non-condensing). . Do not place objects on top of the unit. . Do not obstruct any vents at the sides of the uniL . Do not position the unit near any healing source such as heater, radiator, or direct exposure to sun. Prevent entering of water and moisture into the unit. If necessary, use dehumidifier to reduce humidity. 2. Connecting to network devisee The RJ-45 ports on the switch support Auto-MDIAADI-X function which allows using straight-through or cross-over type cables to connect this switch to workstation or hub. Connect one end ti the network cable to the RJ-45 port on the rear panel, and connect the other end of the network cable to the Redo port on the nehvork device. Follow the same procedure to connect all the RJ-45 ports of the switch. The UTP network cables must comply with EINTIA 588 specifications and Category 5 standard for 100Mbps data transmission. Maximum length: wing LITP cable, between the snitch and connected device is 100 meters (3000). Once the nehvork cable is connected to both ends and the attached network device is powered on, the green LNK/ACT LED should be lit. 4 3.Connecting the power Conned the power adapter to the power connector on the rear panel of the unit; the green Power LED on the front panel should be lit Moulds Shooting 1.Power LED is not lit . Check Bas power cord is properly connected to the e:demal power adapter and the power outlet. Make sure the DC power jack is firmly plugged into the power socket of the switch. 2.Link/Activity le notIf when conned to device . Check the power switch claw nehvork device attached to are switch; make sure it is timed ON. . Check the network cable; make sum it is properly conneded to the switch and the nebsiork device. . Check the network cable; make sure the IITP cables comply with EIAMA 588 and Category 5 seeder:Mon. Ill Cont. your dealer If problem pandit CO- CE FC