Electrolux E30WD75GSS Specification sheet - Page 2

Warmer Drawer, Stand-Alone, Installation, Warmer Drawer/Single Wall Oven, Combination Installation - home products

Page 2 highlights

Warmer Drawer E30WD75GSS designer series 25 1/4" 23 3/8" 30" Overall depth with drawer fully extended (including handle) - 44 1/8" Warmer Drawer Stand-Alone 9 7/8" min. Installation 10 1/4"max. Power cord location (right center rear) 4 1/2" min. required distance to floor 7/8" 11 1/4" 28 1/2" min. 28 3/4" max. 23 5/8" min. 24" max. Full plywood base required to support 100 lbs. 30" Warmer Drawer Specifications • Product Weight - 49 Lbs. • Voltage Rating - 120V / 450W / 60 Hz / 15 Amps • Connected Load (kW Rating) @ 120 Volts = 0.45 kW (For use on adequately wired 120V, dedicated circuit having 2-wire service with a separate ground wire. Appliance must be grounded for safe operation.) • Amps @ 120V = 3.75 Amps • Full plywood base required, capable of supporting 100 Lbs. • Base must be level and cabinet front must be square. • Warmer Drawer can be used alone, or is approved to be used in combination with any Electrolux ICON® Wall Oven. (Refer to Combination Installation Specifications and drawing on this page.) • Warmer Drawer is approved to be used in combination with any Electrolux ICON® High-Speed Oven / Built-In Microwave and / or Electric Single Wall Oven. (Refer to model-specific Combination Installation Specifications pages on web.) Optional Accessories • ServeWare - (PN # 5304447729). Warmer Drawer / Single Wall Oven 11/2" Combination Installation min. 28 1/2" min. 28 7/8" max. 13/4" min.† 9 7/8" min. 10 1/4" max. Two 3" wide x 3/4" thick planks must be installed, capable of supporting 200 lbs. 28 1/2" min. 28 3/4" max. 30" min. 24" * (critical dimension) Electrical junction box location 4" x 4" opening to route armored cable Bottom of oven cutout 11 5/8" min.* 3" max.** *Critical dimension - MUST be applied **Electrical junction box for Wall Oven must be lower than the Warmer Drawer cutout † Maximum height depends on critical dimension (11 5/8") Warmer Drawer / Wall Oven Combination Specifications • To support Wall Oven when using in combination with Warmer Drawer, two 3"-wide x 3/4" thick planks must be installed as a base, capable of supporting 200 Lbs. Do NOT use full base, since planks are necessary to allow for proper air displacement. Note: For planning purposes only. Refer to Product Installation Guide on the web at electroluxicon.com for detailed instructions. Electrolux Major Appliances, N.A. USA • 250 Bobby Jones Expressway • Augusta, GA 30907 • 1-877-4electrolux (1-877-435-3287) • electroluxicon.com CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • electroluxicon.ca E30WD75GSS 09/09 © 2009 Electrolux Home Products, Inc. High standards of quality at Electrolux Home Products, Inc. mean we are constantly working to improve our products. We reserve the right to change specifications or discontinue models without notice. Printed in the U.S.A.

  • 1
  • 2
  • 3
  • 4
  • 5

Warmer Drawer
E30WD75GSS
designer series
High standards of quality at Electrolux Home Products, Inc. mean we are
constantly working to improve our products. We reserve the right to change
specifications or discontinue models without notice.
Electrolux Major Appliances, N.A.
USA
250 Bobby Jones Expressway
Augusta, GA 30907
1-877-4electrolux (1-877-435-3287)
electroluxicon.com
CANADA
5855 Terry Fox Way
Mississauga, ON L5V 3E4
1-800-265-8352
electroluxicon.ca
E30WD75GSS
09/09
© 2009 Electrolux Home Products, Inc.
Printed in the U.S.A.
30" Warmer Drawer Specifications
Product Weight – 49 Lbs.
Voltage Rating –120V/450W/60 Hz/15 Amps
Connected Load (kW Rating) @120 Volts = 0.45kW (For use on
adequately wired 120V, dedicated circuit having 2-wire service with a
separate ground wire. Appliance must be grounded for safe operation.)
Amps @120V = 3.75 Amps
Full plywood base required, capable of supporting 100 Lbs.
Base must be level and cabinet front must be square.
Warmer Drawer can be used alone, or is approved to be used in
combination with any Electrolux ICON
®
Wall Oven.
(Refer to Combination
Installation Specifications and drawing on this page.)
Warmer Drawer is approved to be used in combination with any Electrolux
ICON
®
High-Speed Oven/Built-In Microwave and/or Electric Single Wall
Oven.
(Refer to model-specific Combination Installation Specifications
pages on web.)
Optional Accessories
ServeWare – (PN # 5304447729).
Warmer Drawer/Wall Oven Combination Specifications
To support Wall Oven when using in combination with Warmer Drawer,
two 3"-wide x 3/4" thick planks must be installed as a base, capable of
supporting 200 Lbs. Do NOT use full base, since planks are necessary
to allow for proper air displacement.
Note: For planning purposes only. Refer to Product Installation Guide
on the web at electroluxicon.com for detailed instructions.
Overall depth with
drawer fully extended
(including handle) – 44
1
/
8
"
Full plywood
base required to
support 100 lbs.
4
1
/
2
" min.
required
distance
to floor
9
7
/
8
" min.
10
1
/
4
"max.
28
1
/
2
" min.
28
3
/
4
" max.
23
5
/
8
"min.
24"max.
Warmer Drawer
Stand-Alone
Installation
11
1
/
4
"
23
3
/
8
"
30"
25
1
/
4
"
7
/
8
"
Power cord
location (right
center rear)
9
7
/
8
" min.
10
1
/
4
"max.
1
1
/
2
"
min.
*Critical dimension –
MUST be applied
**Electrical junction
box for Wall Oven
must be lower than
the Warmer Drawer
cutout
Maximum height
depends on critical
dimension (
11
5
/
8
")
3"
max.**
30"min.
4" x 4"
opening
to route
armored
cable
28
1
/
2
"
min.
28
7
/
8
"
max.
Electrical
junction box
location
28
1
/
2
"min.
28
3
/
4
"max.
Bottom
of oven
cutout
11
5
/
8
"
min.*
24"*
(critical
dimension)
Two 3" wide
x
3
/
4
" thick
planks must
be installed,
capable of
supporting
200 lbs.
1
3
/
4
"
min.
Warmer Drawer/Single Wall Oven
Combination Installation