Electrolux E48GC76EPS Specification sheet - Page 2

Gas Slide-In Cooktop E48GC76EPS 13" max. 1/2" cabinet depth Optional 9" stainless steel backsplash (attaches to wall) Side inset 5/8" 2 1/2" min. required distance between rear edge of cooktop and nearest combustible surface above countertop* 25" 22" 3" 24" min. 48" min. 48" 26 1/2" 30" min. for unprotected cabinet 18" min. 24" min. for protected surface 7 3/4" Support platform 1" min. 7 3/4" 10" min. to nearest combustible wall (either side of unit) 11/2" typical countertop edge 46"48" Opening to route gas and electrical supply * If 2 1/2" clearance can not be maintained, then optional stainless steel backsplash or noncombustible backsplash material must be used - otherwise this installation will require custom cabinet and countertop dimensions 48" Gas Slide-In Cooktop Specifications • Product Weight - 190 Lbs. • Voltage Rating - 120V / 60 Hz / 15 Amps • Connected Load (kW Rating) @ 120 Volts = 0.03 kW (For use on adequately wired 120V, dedicated circuit having 2-wire service with a separate ground wire. Appliance must be grounded for safe operation.) • Amps @ 120 Volts = 0.25 Amps • Always consult local and national electric and gas codes. • Cooktop ships with 3/4" factory regulator. • LP Gas conversion kit supplied. • Plan installation to have electrical connection, gas shutoff valve, and pressure regulator accessible from front of cabinet. Locate 120V grounded outlet and gas supply in a 30" W x 15-1/2" H area on rear wall, 10" above floor and 6" to right from center of cooktop. • Overhead cabinetry should not exceed a 13" maximum depth. • Allow 30" minimum clearance between top of cooktop and bottom of unprotected wood or metal overhead cabinetry. • Absolute minimum horizontal distance between overhead cabinets installed to either side of appliance must be no less than maximum width of appliance. • Allow 24" minimum clearance when bottom of wood or metal overhead cabinet is protected by not less than 1/8" flame-retardant millboard covered with not less than No. 28 MGS sheet steel, 0.015" stainless steel, 0.024" aluminum or 0.020" copper. • Allow 2-1/2" minimum clearance between rear edge of cooktop and nearest combustible surface above countertop. If required clearance cannot be maintained, then optional stainless steel backsplash or noncombustible backsplash material must be used - otherwise installation will require custom cabinet and countertop dimensions. • Allow 10" minimum clearance from edge of cooktop to nearest combustible wall on either side of unit. • It is recommended that drawers not be used beneath cooktop. • To reduce risk of fire when using overhead cabinetry, install vent hood that projects horizontally a recommended minimum of 5" beyond bottom of cabinets. • Gas Slide-In Cooktop model E48GC76EPS is NOT approved to be used over any Electrolux ICON® Single Wall Oven. Note: For planning purposes only. Refer to Product Installation Guide on the web at electroluxicon.com for detailed instructions. Optional Accessories • 9" Stainless Steel Backsplash - (PN # ACCBG09-48SI). • Black Gas Valve Knob - (PN # 318313302). Electrolux Major Appliances, N.A. USA • 250 Bobby Jones Expressway • Augusta, GA 30907 • 1-877-4electrolux (1-877-435-3287) • electroluxicon.com CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • electroluxicon.ca E48GC76EPS 04/10 © 2010 Electrolux Home Products, Inc. High standards of quality at Electrolux Home Products, Inc. mean we are constantly working to improve our products. We reserve the right to change specifications or discontinue models without notice. Printed in the U.S.A.