Electrolux EI23BC56IW Use and Care Guide - Page 13

Connecting the Water u ply 13 WARNING To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator from electrical power before connecting a water supply line to the refrigerator. CAUTION To Avoid Property Damage: • Copper or Stainiees Steel braided tubing is recommended for the water supply line. Water supply tubing made of 1Ainch plastic is not recommended to be used. Plastic tubing greatly increases the potential for water leaks, and the manufacturer will not be responsible for any damage if plastic tubing is used for the supply line. • DO NOT install water supply tubing in areas where temperatures fall below freezing. • Chemicals from a malfunctioning softener can damage the ice maker, if the ice maker is connected to soft water, ensure that the softener is maintained and working properly. IMPORTANT Ensure that your water supply line connections comply with all local plumbing codes. Before Installing The Water Supply Line, You Will Need: ,, Basic Tools: adjustable wrench, flat-blade screwdriver, and Phillips TM screwdriver - Access to a household cold water line with water pressure between 30 and 100 psi. ,, A water supply line made of ¼ inch (6.4 mm) OD, copper or stainless steel tubing.To determine the length of tubing needed, measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water pipe. Then add approximately 7 feet (2.1 meters), so the refrigerator can be moved out for cleaning (as shown). ,, A shutoff valve to connect the water supply line to your household water system. DO NOT use a self-piercing type shutoff valve. ,, A compression nut and ferrule (sleeve) br connecting a copper water supply line to the ice maker inlet valve. NOTE Check with your local building authority for recommendations on water linesand associated materials prior to installing your new refrigerator. Depending on your local/state building codes, Electrolux recommends for homes with existing valves its Smart Choice@water line kit 5305513409 (with a 6 ft. Stainless Steel Water Line) and for homes without an existing valve, Electrolux recommends its Smart Choice water_ line kit 5305510264 (with a 20 ft. Copper Water Line with self-tapping saddle valve). Please refer to www.frigidaire.corrVstorefor more information. To Connect Water Supply Line To tee Maker Inlet Valve 1. Disconnect refrigerator from electric power source. 2. Place end of water supply line into sink or bucket. Turn ON water supply and flush supply line until water is clear.Turn OFF water supply at shutoff valve. 3. Remove plastic cap from water valve inlet and discard cap. 4. If you use copper tubing - Slide brass compression nut, then ferrule (sleeve) onto water supply line. Push water supply line into water valve inlet as far as it will go (¼ inch / 6.4 mm). Slide ferrule (sleeve) into valve inlet and finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT over tighten. See Figure 1. If you use stainless steel tubing -The nut and ferrule are already assembled on the tubing. Slide compression nut onto valve inlet and finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT over tighten. See Figure 2. 5. Wilh sleelclamp and screw,securewater supplyline (copperlubing only)to rear panelof refrigerabras shovm. 6. Coil excess water supply line (copper tubing only), about 2V2 turns, behind refrigerator as shown and arrange coils so they do not vibrate or wear again st any other surface. 7. Turn ON water supply at shutoff valve and tighten any connections that leak. 8. Reconnect refrigerator to electrical power source. 9. To turn ice maker on, lower wire signal arm (side mounted) or set the ice maker's On/Off power switch to the "!" position (rear mounted). Figure 1 Figure 2 iMPORTANT After connecting the water supply, refer to "How to Prime the Water Supply System" for important information about priming an empty 'water supply system. Your refrigerator's water supply system includes several tubing lines, a water filter, a water valve, and a water tank_ To ensure that your water dispenser works properly, this system must be completely filled with water when your refrigerator is first connected to the household water supply line.