Electrolux EI23CS35KS Wiring Diagram (English Español França - Page 1

PERFORMANCE DATA NO LOAD & NO DOOR OPENINGS AT 0° F FREEZER & 37° F FRESH FOOD (2500 ++ V5) Type A with Run/Start Capacitor 65°F (18°C) Ambient Variable Speed Standard 90°F (32°C) Ambient Variable Speed Standard Operating Time 74 to 84% 32 to 40% 100% 55 to 65% Freezer Temperature -2° to 2° F -19° to -17° C 0° to 4° F -18° to -16° C -1° to 3° F -18° to -16° C -1° to 3° F -18° to -16° C Refrigerator Temperature 34° to 39° F 1° to 4° C 34° to 39° F 1° to 4° C 34° to 39° F 1° to 4° C 34° to 39° F 1° to 4° C Low Side Pressure (cut-in) 5 to 12 psig 43 to 83 kPa 5 to 12 psig 43 to 83 kPa N/A 5 to 12 psig 43 to 83 kPa Low Side Pressure (cut-out) -2 to 2 psig -14 to 14 kPa -2 to 2 psig -14 to 14 kPa -2 to 2 psig -14 to 14 kPa -2 to 2 psig -14 to 14 kPa High Side Pressure (last 1/3 cycle) 90 to 105 psig 90 to 115 psig 120 to 135 psig 130 to 155 psig 621 to 724 kPa 621 to 793 kPa 827 to 931 kPa 896 to 1069 kPa Wattage (last 1/3 cycle) 50 to 60 90 to 130 60 to 70 100 to 140 Amps (running) 0.5 to 0.9 0.7 to 1.1 0.6 to 1.0 0.8 to 1.2 Base Voltage 115 vac (127 vac max) DEFROST SPECIFICATIONS Cabinet Size Thermostat Cut-in Cut-out Watts Heater Ohms 23' CD, 26' 25° F (-4° C) 47° F (8° C) 450 30 Electronic Timer - (ADC) Defrost 24 minutes every 6-96 hours of compressor run time. CONDENSER FAN MOTOR Watts RPM Amps 3.1 1100 CW Opposite Shaft 0.03 Running Variable Capacity Compressor (VCC) Diagnostics (select models) If test 38 fails, diagnose as follows: → Check at the connector from the power cord harness into the inverter board, located in the machine compartment. (PUR and WHT wires) Is Inverter Board receiving 115 VAC from power supply? → Check at Inverter Board on Compressor yes (BLK and RED wires) Is Inverter Board receiving 10-15 VAC and 1-5 VDC from Main Control Board? → Remove inverter box from the compressor and check resistance yes across compressor winding pairs as shown. Is resistance across all winding pairs equal? → Check connections from Inverter Board to Compressor yes Are connections from Inverter Board to Compressor intact? no SERVICE DATA SHEET 240389648 ICE & WATER - AUTOMATIC DEFROST SIDE BY SIDE - R134a IMPORTANT: PLEASE RETURN THIS SHEET TO ITS ORIGINAL LOCATION Error Codes Display FZ FF Interpretation -- OP- Open FF mid-level thermistor -- OP¯ Open FF upper-level thermistor OP -- Open FZ thermistor Shorted FF mid-level -- SH- thermistor -- SH¯ Shorted FF upper-level thermistor SH -- Shorted FZ thermistor UI to Main Control Board SY CF communication failure; on start up SY CE UI Main Control Board communication error; after a period in operation SY EF Evaporator fan failure Special Modes Mode Display FZ FF Activate/Deactivate (press for up to 10 sec. simultaneously) Manual d F FF UP and FF DOWN/ Defrost same to deactivate Display/ 77 Showroom 77 FZ UP and FF DOWN/ Power-on-Reset (POR) Sabbath Sb Sb FZ DOWN and FF UP/ same to deactivate Diagnostic No FF or FZ display, FZ UP and FZ DOWN/FF all UI LEDs on. UP to deactivate Notes: • Always check for pin back-outs, pinched or damaged wires before replacing components. • Determine whether failure is caused by the component, main control board or wiring. Contact TID before replacing main control board. • Refer to Service Manual for additional information. no no no • Check voltage supply. • Check and repair power cord harness wiring and connections. Replace Compressor and Inverter Board. Replace Main Control Board. Identify and repair damaged wires or poor connections between Inverter Board and Compressor. yes → Check at Main Control Board (BLK/WHT and RED/BLK wires) no Is Main Control Board sending 10-15 VAC and 1-5 VDC to Inverter Board? Replace Inverter Board yes VCC Resistance Check Check resistance between terminals 1 and 2, 2 and 3, 3 and 1. If all resistances are equal, compressor is operative. Identify and repair damaged wires or poor connections between Main Control Board and Inverter Board. Diagnostic Mode Activate: Press FZ UP and FZ DOWN temperature pads for up to 10 sec. simultaneously. Press FF UP to advance through tests. Deactivate: Press FF UP for up to 10 sec. Diagnostic Mode will automatically deactivate after 5 min. of inactivity. Note: Silence alarm. • Tests marked with "*" may not be applicable to this unit and will not be displayed in Diagnostic Mode. • Tests displayed in diagnostic mode but not described below are for internal purposes only; advance through. • View UI display for "on," "off," "CL," "OP," "SH," "LO," "HI" or numerical results of tests. • Listen for operating sounds; feel for heat or air flow as appropriate to determine results of tests. Test To activate test: Passing result -- First Screen -- All LED lights on UI illuminated -- Second Screen -- All segments on UI temperature displays illuminated -- Third Screen -- Blank UI display, no lights illuminated, no shadowing; "-" and "+" blinking on FF display side to show location. 28 Dispenser Paddle Press disp. paddle "on" on UI when depressed; "off" when released 1* Standard Compressor Press power on-off Compressor running when "on"; stopped when "off" 2 Defrost Heater Press power on-off Defrost limit switch must be closed; verify "CL" in test 26. Feel for heat from defrost heater when "on". If "OP" in test 26, heater will not activate. 3 FF Light Press power on-off With FF door open, FF lights on when "on"; off when "off" 8 Water Valve (Dispenser) Press power on-off FF door must be closed. Be prepared to collect water at dispenser. Water dispenses when "on"; stops when "off" 9 FZ Light Press power on-off With FZ door open, FZ lights on when "on", off when "off" 10 Auger Motor Press power on-off FF door must be closed. Motor running when "on"; motor stopped when "off" 11 Cube/Crush Solenoid Press power on-off FF door must be closed. Do not leave solenoid in activated state. Solenoid activated when "on"; deactivated when "off" 41* Perfect Temp Drawer Press power on-off (PTD) PTD UI illuminated when "on", off when "off" 12* VCC Condenser Fan Press power on-off Fan running when "on"; stopped when "off" 38* VCC Compressor Press power on-off Compressor running when "on"; stopped when "off" 15 Evaporator Fan Press power on-off Fan running for minimum of 10 sec. when "LO" or "HI"; stopped when "off". Feedback failure if fan starts but runs less than 10 sec. Listen for speed change from "LO" to "HI". 22 Damper Press power on-off With inspection mirror, observe damper open when "OP"; closed when "CL" 23 FF Door Open/close FF door "CL" on UI when door closed; "OP" when open 24 FZ Door Open/close FZ door "CL" on UI when door closed; "OP" when open 26 Defrost Limit Switch Activates automatically "CL" on UI when closed; "OP" when open 36 Ice Chute Door Depress ice chute door "OP" on UI when manually opened; "CL" when closed. Or, using "power or press power on-off on-off", "OP" on UI when solenoid activated, "CL" when deactivated 29 FF Thermistor Mid-level Activates automatically UI shows temperature sensed by FF thermistor; pass if within 10°F of temperature measured with gauge at mid-level FF thermistor location. "OP-" if open; "SH-" if short 30 FZ Thermistor Activates automatically UI shows temperature sensed by FZ thermistor; pass if within 10°F of temperature measured with gage at FZ thermistor location. "OP" if open; "SH" if short 33 Ambient Thermistor Activates automatically UI shows temperature sensed at main board; pass if within +20°F/-10°F @ Main Board of temperature measured with gauge at main board location. "OP" if open; "SH" if short 35 FF Thermistor Upper-Level Activates automatically UI shows temperature sensed by upper level FF thermistor; pass if within 10°F of temperature measured with gauge at upper-level FF thermistor location. "OP¯" if open; "SH¯" if short 34 Ambient Thermistor Activates automatically UI shows temperature sensed at UI; pass if within +20°F/-10°F of tem- @ UI perature measured with gauge at UI location. "OP" if open; "SH" if short 0- Firmware Parameters Press power on-off Displays digit sequence; record 2- Main Board Firmware Press power on-off Displays digit sequence; record 4- UI Firmware Press power on-off Displays digit sequence; record IMPORTANT SAFETY NOTE The information provided herein is designed to assist qualified repair personnel only. Untrained persons should not attempt to make repairs due to the possibility of electrical shock. Disconnect power cord before servicing this appliance. IMPORTANT If any green grounding wires are removed during servicing, they must be returned to their original position and properly secured. CAUTION All electrical parts and wiring must be shielded from torch flame. DO NOT allow torch to touch insulation; it will char at 200°F and flash ignite (burn) at 500°F. Excessive heat will distort the plastic liner.