Electrolux EIDW6105GS Wiring Diagram (All Languages) - Page 1
Electrolux EIDW6105GS - Fully Integrated Dishwasher Manual
UPC - 012505110498
View all Electrolux EIDW6105GS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
Exploded View of Wash System Standard Dry Air Flow Trouble Shooting Tips When the control advances to the "dry" portion of the cycle, the lower fan located in the Lower Drying Duct Assembly is activated. Then, the Vent Assembly located in the top right corner of the tub is activated. The vent fan draws in the air from outside the tub forcing the hot, humid air out the Side Drying Duct Assembly and into the Lower Drying Duct Assembly. Cool dry outside air is mixed with hot, humid air existing the tub in the Lower Drying Duct Assembly. This lowers the temperature and humidity of the air exiting the unit through the toe and kickplate. The addition of cooler, dryer outside air helps to speed evaporation of water from the hot dishes. Personal Injury Hazard Always disconnect the dishwasher from the electrical power source before adjusting or replacing components. Symptom Check the Following Remedy Dishwasher will not operate when turned on. Detergent and Rinse Aid Dispenser The detergent and rinse aid dispenser is a one piece component consisting of a molded detergent cup and a built-in rinse aid dispenser. The detergent cup has a spring loaded cover and the rinse aid dispenser has a removable cover. Liquid rinse aid is added to the dispenser up to the fill line indicator. The amount of rinse aid released can be adjusted by turning the arrow indicator from one, being the least amount, to four, being the greatest amount. To replace dispenser: • shut off electricity to dishwasher, • remove outer door panel assembly and foam barrier, • disconnect wiring to the dispenser, • remove the six screws and bracket, • remove the dispenser, • replace and reinstall in reverse order, • rewire actuator. Motor hums but will not start or run. Motor trips out on internal thermal overload protector. 1. Fuse (blown or tripped). 2. 120 VAC supply wiring connection faulty. 3. Electronic control board defective. 4. No 12 VAC power to control. 5. Motor (inoperative). 6. Door switch (open contacts). 7. Door latch not making contact with door switch. 8. Touch pad circuit defective. 9. No indicator lamps illuminate when START or OPTIONS are pressed. 1. Replace fuse or reset breaker. 2. Repair or replace wire fasteners at dishwasher junction box. 3. Replace control board. 4. Replace control board. 5. Replace motor/impeller assembly. 6. Replace latch assembly. 7. Replace latch assembly. 8. Replace console assembly. 9. Replace console assembly. 1. Motor (bad bearings). 2. Motor stuck due to prolonged non-use. 1. Replace motor assembly. 2. Rotate motor impeller. 1. Improper voltage. 2. Motor windings shorted. 3. Glass or foreign items in pump. 1. Check voltage. 2. Replace motor/impeller assembly. 3. Clean and clear blockage. Dishwasher runs but will not heat. Tub Gasket Detergent cover will not latch or The door gasketl is pressed into the tub channel 3. Press the gasket while stretching around open. for an interference fit. To install the gasket: the corners . 1. Locate the center mark on the gasket and NOTE: There should be no wrinkles or a press into place. puckers in the corners. 2. Press the gasket across the header using 4. Place the gasket end at the bottom and Dishwasher will not pump out. your thumb. then press the gasket in from the bottom up. Pump Assembly The pump assembly is driven by a permanent split capacitor motor. When looking at the output shaft, rotation is in the counterclockwise direction at 3300RPM when driven by 120V 60Hz AC signal. The motor drives a pump which supplies 100% filtered water at the rate of approximately 19 GPM to all three spray arms at once. The drain valve is connected to the drain pump by a rubber hose and is mounted to the dishwasher base. The drain valve maintains pressure in the pressurized fine filter. The intermediate drain hose is attached by a worm gear clamp to the discharge end of the drain valve. Draining is accomplished by using a small seperate synchronous drain pump mounted to the sump. The drain pump is connected to the sump by a small rubber hose and two mounting points. A check valve is located at the discharge end of the drain pump. Component Error LED Indication The drain hose must have a loop at a minimum height of 32 inches in order to ensure proper drainage. The main pump is removed by disconnecting both attached clamps and hoses, removing the three screws that secure the motor base to the dishwasher base, unlatching the leak detector, and disconnecting the wiring harness connections to the pump assembly. To gain access to the Control Housing Assembly, remove kickplate assembly. LED indicates which component is the source of the error. Product Specifications Electrical Rating 120 Volts, 60Hz Separate Circuit..15 amp min.- 20 amp max. Motor (Amps 75 Heater Wattage 1200 Total Amps (load rated 10.0 TempAssure 140°F ±5°F (60°C±3°C) [with outer door in place] TempBoost 145°F ±5°F (63°C ±3°C) Heated Wash/Heated Rinse Sanitize 150°F ±5°F (66°C ±3°C) Hi-Limit Thermostat 200°F (93°C) Dishwasher will not fill with water. Dishwasher water siphons out. Water Supply Suggested minimum incoming water temperature 120°F (49°C) Pressure (PSI) min./max 20/120 Connection (NPT 3/8" Consumption (Normal Cycle 4.9 - 9.7 U.S. gal., 18.5 - 36.7 liters Water valve flow rate (U.S. GPM 83 Water recirculation rate (U.S. GPM approx. 19 Water fill time 87 sec. Detergent left in dispenser. 1. Heater element (open). 2. Electronic control board defective. 3. Wiring or terminal defective. 4. Hi-Limit thermostat defective. 1. Replace heater element. 2. Replace control board. 3. Repair or replace. 4. Replace thermostat. 1. Latch mechanism defective. 2. Electronic control board defective. 3. Wiring or terminal defective. 4. Broken spring(s). 5. Defective actuator. 1. Replace dispenser. 2. Replace control board. 3. Repair or replace. 4. Replace dispenser. 5. Replace dispenser. 1. Drain restricted. 2. Electronic control board defective. 3. Defective drain pump. 4. Blocked impeller. 5. Open windings. 6. Wiring or terminal defective. 7. Defective Drain Valve. 1. Water supply turned off. 2. Defective water inlet fill valve. 3. Check fill valve screen for obstructions. 4. Defective float switch. 5. Electronic control board defective. 6. Wiring or terminal defective. 7. Float stuck in "UP" position. 1. Clear restrictions. 2. Replace control board. 3. Replace pump. 4. Check for blockage, clear. 5. Replace pump assembly. 6. Repair or replace. 7. Repair or replace. 1. Turn water supply on. 2. Replace water inlet fill valve. 3. Disassemble and clean screen. 4. Repair or replace. 5. Replace control board. 6. Repair or replace. 7. Clean or replace float. 1. Drain hose (high) loop too low. 2. Drain line connected to a floor drain not vented. 3. Drain valve or pump stuck open. 1. Repair to proper 32-inch minimum height. 2. Install air gap at counter top. 3. Repair or replace. 1. Detergent allowed to stand too long in dispenser. 2. Dispenser wet when detergent was added. 3. Detergent cover held closed or blocked by large dishes. 4. Improper incoming water temperature to properly dissolve detergent. 5. See "Detergent cover will not open." 6. Spray arm blocked. 7. Is water getting into unit. 1. Instruct customer/user. 2. Instruct customer/user. 3. Instruct customer/user on proper loading of dishes. 4. Incoming water temperature of 120°F is required to properly dissolve dishwashing detergents. 6. Instruct customer/user. 7. Check fill valve repair or replace. 010108