Electrolux EIMGD60LSS Operating Instructions (Operating Instructions) - Page 1

WARNING • Dryer must be properly grounded at all times. • Vent dryer through free-flowing, outdoor-vented, metal duct system. • Improper gas installation or LP conversion could result in injury or even death. • Avoid back or other injury. Use more than one person to move, tip or lift the dryer. IMPORTANT Please read all safety instructions before using your new front-loading dryer. For best drying results with your new dryer, remember to review: 9 INSTALLATION INSTRUCTIONS 9 USE & CARE GUIDE NOTE TO INSTALLER Leave these instructions with the customer. REMARQUE POUR L'INSTALLATEUR Laissez ces instructions au client. Suite de la version française au verso. NOTA AL INSTALADOR Deje estas instrucciones con en cliente. Español continua en la pagina trasera. UNPACKING & HANDLING A) EMPTY DRUM CONTENTS B) CAREFULLY TIP PROTECT FLOOR C) CART FROM REAR ONLY WITH 7" MIN. CART FORKS 2-PERSON CARRYING STRAPS, FRONT-TOBACK RECOMMENDED DO NOT CART FROM FRONT DO NOT CART FROM SIDE REMOVE & SAVE D) RETURN UPRIGHT DO NOT USE KNEE IN CABINET SIDE TO MOVE UNIT DO NOT USE OPEN DOOR TO LIFT OR TIP THE UNIT VENT EXHAUST •USE ONLY 4 INCH (10.2 CM) RIGID METAL OR SEMI-RIGID METAL DUCTING •REPLACE PLASTIC OR FOIL DUCTS WITH METAL •CLEAN LINT FROM PRESENT DUCT SYSTEM BEFORE ADDING ON •SEE CHART TO THE RIGHT FOR ACCEPTABLE NUMBER OF 90° TURNS IN SYSTEM •DO NOT USE SCREWS TO CONNECT DUCTS • DO NOT USE REGULAR DUCT TAPE TO CONNECT DUCTS, ONLY METAL FOIL TAPE •4" (10.2 cm) CLAMP RECOMMENDED FOR CONNECTION BETWEEN DRYER & EXHAUST SYSTEM •EXHAUST SYSTEM MUST BE VENTED OUTSIDE WITH APPROVED VENT HOOD •TO VENT LEFT OR RIGHT FROM DRYER, USE 90° QUICKTURN ELBOW •FOR INSTALLATION IN A RECESSED AREA OR CLOSET, SEE COMPLETE INSTALLATION INSTRUCTIONS •FOR MOBILE HOME INSTALLATION, SEE COMPLETE INSTALLATION INSTRUCTIONS Number of 90° turns MAXIMUM LENGTH of 4" (10.2cm) Rigid Metal Duct VENT HOOD TYPE (Preferred) 4" (10.2cm) louvered 2.5" (6.35cm) 0 125 ft. (38.0m) 110 ft. (33.5m) 1 115 ft. (35.0m) 100 ft. (30.5m) 2 105 ft. (32.0m) 90 ft. (27.5m) 3 95 ft. (29.0m) 80 ft. (24.5m) 4 85 ft. (26.0m) 70 ft. (21.5m) *Do not install plastic or foil ducting. If installing semi-rigid ducting, do not exceed 8 ft (2.4 m) total duct length. IMPORTANT For pedestal, stacked or closet installations, see detailed installation instructions enclosed. CORRECT INCORRECT HEAT SOURCE GAS DRYER WRENCH-TIGHT MANUAL SHUTOFF APPLY APPROVED THREAD SEALANT. REFER TO INSTALLATION INSTRUCTIONS FOR MORE DETAILED INFORMATION. ELECTRIC DRYER L.P. SYSTEMS MUST USE COVERSION KIT INSTALLED BY QUALIFIED TECHNICIAN. 30 AMP DON'T MOVE 30 AMP MOVE GROUND WHITE GREEN RED OR BLACK INSTALL U.L.-APPROVED STRAIN RELIEF RED OR BLACK CONNECT WATER IF THIS IS NOT A STEAM DRYER, SKIP TO STEP 5. A) B) C) D) E) TURN OFF WATER SUPPLY TO WASHER. F) COLD WATER SUPPLY HOSE TO WASHER. REMOVE COLD WATER HOSE FROM COLD WATER SUPPLY. INSPECT RUBBER WASHER. REPLACE IF WORN. USE HOSE EXTENSION IF "Y" CONNECTOR CANNOT ATTACH DIRECTLY TO COLD WATER SUPPLY. WATER INLET ON DRYER. G) RUN WATER FROM COLD OUTLET TO CLEAR CONTAMINANTS. REMOVE FROM BAG. INSPECT FOR RUBBER WASHERS. H) I) TIGHTEN ALL CONNECTIONS BY HAND. TIGHTEN ADDITIONAL 2/3 TURN WITH PLIERS. CONNECT "Y" FIXTURE OR EXTENSION HOSE TO COLD SUPPLY. TIGHTEN BY HAND. TIGHTEN ADDITIONAL 2/3 TURN WITH PLIERS. TURN ON WATER AND CHECK FOR LEAKS. LEVEL & CONNECT OPERATE Perform brief installation cycle for your model as follows: C) If dryer has this console: B) If dryer has this console: A) ADJUST raise lower D) CONNECT POWER CAUTION ELECTRICAL SHOCK HAZARD Do NOT use prong adapter. Do NOT remove ground prong. Do NOT use extension cord. LEVEL BOTH WAYS CHECK STABILITY, CORNER-TO-CORNER E) OPEN GAS VALVE AND CHECK FOR LEAKS WITH SOAPY WATER 1. Empty dryer drum and close door. 2. Wake dryer up (any button), rotate cycle knob to touch up, press start then cancel. 3. Wake dryer up again, immediately and simultaneously press and hold sanitize and my favorite buttons for 5 seconds. 4. LCD will display INSTAL CYCLE and show estimated time of cycle completion. Press start. 5. Installation Cycle will perform various diagnostic routines. 6. At cycle completion, LCD will display INSTAL PASS! or prompt an action during cycle such as SERVICE CORD, NO GAS or CALL SERVICE 877 435 3287. 7. Dryer will exit the Installation Cycle and return to normal operation next time you wake it up. Read Use and Care Guide and enjoy your new premium dryer! 1. Empty washer drum and close door. 2. Wake up the dryer by pressing any button and then follow the prompts on the LCD User Interface, including language selection. NOTE: this initial, automatic cycle can be manually accessed through the scroll buttons in the set prefs sections under options. 3. LCD will display INSTAL CYCLE and show estimated time of cycle completion. Press start. 4. Installation Cycle will perform various diagnostic routines. 5. At cycle completion, LCD will display INSTAL PASS! or prompt an action during cycle such as SERVICE CORD, NO GAS or CALL SERVICE 877 435 3287. 6. Dryer will exit the Installation Cycle and return to normal operation next time you wake it up. Read Use and Care Guide and enjoy your new premium dryer! CLEAN LINT FILTER AFTER EVERY LOAD. NETTOYEZ LE FILTRE À CHARPIE APRÈS CHAQUE SÉCHAGE. LIMPIE EL FILTRO DE PELUSAS DESPUÉS DE CADA CARGA. For toll-free telephone support in the U.S. and Canada: 1-877-4ELECTROLUX (1-877-435-3287). For online support and product information, visit http://www.electroluxappliances.com. Pour rejoindre le service sans frais aux États-Unis et au Canada: 1-877-4ELECTROLUX (1-877-435-3287). Pour obtenir de l'aide et de l'information sur les produits en ligne, visitez le site http://www.electroluxappliances.com. Para obtener asistencia telefónica gratuita en los Estados Unidos y Canadá: 1-877-4ELECTROLUX (1-877-435-3287). Para obtener asistencia e información en Internet sobre el producto, visite http://www.electroluxappliances.com. 137269500A (0911)