Electrolux EW36IC60I Use and Care Guide - Page 21

Electrolux EW36IC60I - 36 in. Induction Cooktop Manual

Page 21 highlights

Solutions to Common Problems COOKmNG ZONE H_TS FOODTOO HOT OR NOT HOT ENOUGH Incorrect power level setting. Adjust the power level setting higher or lower and refer to recipe for guidance and adjust accordingly. FOOD DOES NOT HEAT EVENLY Lightweight or warped pans were used. Be sure to use good quality cookware. Use only flat bottom, evenly balanced medium or heavyweight cookware. Heavy and medium weight pans heat evenly. Because lightweight pans heat unevenly, foods may burn more easily (See pages 9 to 11 for further information). Adjust Cooking Zone power level setting until the proper amount of heat is obtained. • POORCOOKINGRESULTS Many factors affect cooking results. Adjust the recipe's recommended power levels or cooking times. Cookware is too lightweight or warped. Use heavier quality cookware so foods being prepared may cook more evenly. COOKTOP ZONE CONTROLS DmSPLAYERROR CODE If an error occurs that affects a zone, that zone will display an error and that specific zone will shut down. If the error affects more than one zone but a single Induction Heater, then the zones affected by that Induction Heater will display an error and those specific zones will shut down. However if an error occurs that affects the whole cooktop, then the error will display in all zones and the whole cooktop will shut down. If any error occurs try shutting power down to the cooktop then reapply power. If the error persists then call Electrolux 1-877-4ELECTROLUX (1-877-435-3287). cooK zo.Es .G E..ER LED co .uousLY ROTAT,NGAROUND D,G_TALD,SPLAY, , , , , , • . Induction Cooktop pan detection sensors do not see the correct cookware. Test with a magnet to be sure cookware is made with Induction compatible material. Cookware has been removed from the Cooking Zone without turning the Cooking Zone OFF. Place cookware back on to the Cooking Zone or if finished cooking turn OFF the affected Cooking Zone. Cookware is not centered over the Cooking Zone properly. Refer to page 10 for correct cookware placement. .

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24

Solutions
to Common
Problems
COOKmNGZONE H_TS
FOODTOOHOT
OR
NOTHOTENOUGH
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
Incorrect
power level setting. Adjust
the power
level setting
higher
or lower and refer
to recipe for guidance
and adjust
accordingly.
FOOD DOES NOT HEAT EVENLY
_
[]
[]
[]
_
[]
[]
_
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
Lightweight
or warped
pans were used. Be sure to use good quality
cookware.
Use only flat bottom,
evenly
balanced
medium
or heavyweight
cookware.
Heavy and
medium
weight pans heat evenly. Because
lightweight
pans heat unevenly, foods may
burn more easily
(See pages 9 to 11 for further
information).
Adjust
Cooking
Zone power level setting until the proper
amount
of heat is obtained.
POORCOOKINGRESULTS
_
[]
[]
[]
_
[]
[]
_
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
Many factors
affect cooking
results. Adjust
the recipe's
recommended
power levels or
.
cooking
times.
Cookware
is
too lightweight
or warped.
Use heavier
quality
cookware
so foods
being
prepared
may cook
more evenly.
COOKTOP ZONE CONTROLS DmSPLAYERROR CODE
[] .[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
[]
Ifan error occurs that affects a zone, that zone will display an error and that specific zone
will shut down.
If the error affects
more than one zone but a single
Induction
Heater,
then the zones affected by that Induction
Heater will display
an error and those specific
zones will shut down.
However
if an error occurs that affects the whole cooktop,
then
the error will display
in all zones
and the whole
cooktop
will shut down.
If any error
occurs try shutting
power down to the cooktop
then reapply power.
If the error persists
then call Electrolux
1-877-4ELECTROLUX
(1-877-435-3287).
cooK .G
zo.Es
E..ER
LED
co .uousLY
ROTAT,NGAROUND D,G_TALD,SPLAY,
,
,
,
,
,
Induction Cooktop
pan detection
sensors
do not see the correct cookware.
Test with a
.
magnet
to be sure cookware
is made with
Induction
compatible
material.
Cookware
has been removed from the Cooking Zone without turning the Cooking Zone
OFF. Place cookware
back on to the Cooking
Zone or if finished
cooking
turn OFF the
.
affected
Cooking
Zone.
Cookware
is not centered
over the Cooking
Zone properly.
Refer to page 10 for correct
cookware
placement.