Electrolux EWMED70JIW Complete Owner's Guide (English) - Page 26

Setting Preferences, continued

Get Electrolux EWMED70JIW PDF manuals and user guides
UPC - 012505382840
View all Electrolux EWMED70JIW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

26 Operating User Interface Features Setting Preferences, continued INSTALL CYCLE Run the INSTALL CYCLE before operating the dryer the first time. Remove all items from the dryer drum and press start. For more information on performing the dryer INSTALL CYCLE, refer to the Installation Instructions accompanying this dryer. If the dryer has been installed according to Installation Instructions, INSTALL PASS! will be displayed and the dryer is ready to use. If the dryer was not installed properly, SERVICE CORD, NO GAS or CALL SERVICE 877 435 3287 will be displayed to indicate the installation error. The errors may result from the following conditions: • SERVICE CORD (electric dryer)-The power supply cord has been installed improperly or the house wiring to the receptacle is incorrect. • NO GAS (gas dryer)-There is no connection between the dryer and the gas line or the valve is closed. • CALL SERVICE-Error can only be corrected by calling a qualified technician (1-877-435-3287). Repeat the INSTALL CYCLE when corrections are completed. RESET Press the buttons indicated to restore only cycle settings, reset only factory preferences (users, language, brightness, volume, etc.) or restore all factory defaults (both cycle settings and factory preferences). Press the button under EXIT to return to normal operation or press the cancel button to turn the dryer off without making any changes. If you do not make a selection within 30 seconds the dryer will return to normal operation without any changes. If you reset all settings, INSTALL CYCLE will be displayed as though the dryer were just turned on for the first time. You may press the button under CANCEL if you do not wish to rerun the INSTALL CYCLE. CONTRAST Press the button beneath plus (+) or minus (-) symbols to increase or decrease the contrast of the display. Press select to accept the change or press the button under EXIT to return to normal operation without any changes. NOTE The INSTALL CYCLE is prompted automatically only once when the dryer is turned on the first time at the end of installation. After that, if you wish to run a subsequent INSTALL CYCLE when moving the dryer or modifying your installation, you may perform your own INSTALL CYCLE by selecting it in the set prefs feature and then following the screen prompts.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
26
Operating User Interface Features
Setting Preferences, continued
INSTALL CYCLE
Run the
INSTALL CYCLE
before operating the dryer
the first time. Remove all items from the dryer drum
and press
start
. For more information on performing
the dryer
INSTALL CYCLE
, refer to the
Installation
Instructions
accompanying this dryer.
If the dryer has been installed according to
Installa-
tion Instructions
,
INSTALL PASS!
will be displayed
and the dryer is ready to use.
If the dryer was not installed properly,
SERVICE
CORD
,
NO GAS
or
CALL SERVICE 877 435 3287
will be displayed to indicate the installation error.
The errors may result from the following conditions:
SERVICE CORD
•
(electric dryer)—The power sup-
ply cord has been installed improperly or the house
wiring to the receptacle is incorrect.
NO GAS
•
(gas dryer)—There is no connection between
the dryer and the gas line or the valve is closed.
CALL SERVICE
•
—
Error can only be corrected by
calling a qualified technician (1-877-435-3287).
Repeat the
INSTALL CYCLE
when corrections are
completed.
RESET
Press the buttons indicated to restore only cycle set-
tings, reset only factory preferences (users, language,
brightness, volume, etc.) or restore all factory defaults
(both cycle settings and factory preferences). Press
the button under
EXIT
to return to normal opera-
tion or press the
cancel
button to turn the dryer off
without making any changes. If you do not make a
selection within 30 seconds the dryer will return to
normal operation without any changes. If you reset
all settings,
INSTALL CYCLE
will be displayed as
though the dryer were just turned on for the first time.
You may press the button under
CANCEL
if you do
not wish to rerun the
INSTALL CYCLE
.
CONTRAST
Press the button beneath plus (+) or minus (-) sym-
bols to increase or decrease the contrast of the
display. Press
select
to accept the change or press
the button under
EXIT
to return to normal operation
without any changes.
NOTE
The
INSTALL CYCLE
is prompted automatically
only once when the dryer is turned on the
first time at the end of installation. After that,
if you wish to run a subsequent
INSTALL
CYCLE
when moving the dryer or modifying
your installation, you may perform your own
INSTALL CYCLE
by selecting it in the
set prefs
feature and then following the screen prompts.