Electrolux FER641FS Installation Instructions - Page 5

Location Of Your Dryer

Get Electrolux FER641FS PDF manuals and user guides View all Electrolux FER641FS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

5. A 1/8 inch (0.32 cm) N.P.T. plugged tapping, accessible for test gauge connection, MUST be installed immediately upstream of the gas supply connection to the dryer. 6. The dryer MUST be disconnected from the gas supply piping system during any pressure testing of the gas supply piping system at test pressures in excess of 1/2 psig (3.45 kPa). 7. The dryer MUST be isolated from the gas supply piping system during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.45 kPa). LOCATION OF YOUR DRYER DO NOT INSTALL YOUR DRYER: 1. In an area exposed to dripping water or outside weather conditions. 2. In an area where it will come in contact with curtains, drapes, or anything that will obstruct the flow of combustion and ventilation air. 3. On carpet. Floor MUST be solid with a maximum slope of 1 inch (2.54 cm). INSTALLATION IN RECESS OR CLOSET 1. A dryer installed in a bedroom, bathroom, recess or closet, MUST be exhausted outdoors. 2. No other fuel burning appliance shall be installed in the same closet as the Gas dryer. 3. Your dryer needs the space around it for proper ventilation. DO NOT install your dryer in a closet with a solid door. 4. A minimum of 120 square inches (774.2 square cm) of opening, equally divided at the top and bottom of the door, is required. Air openings are required to be unobstructed when a door is installed. A louvered door with equivalent air openings for the full length of the door is acceptable. MINIMUM INSTALLATION CLEARANCES - Inches (cm) SIDES REAR TOP FRONT Alcove 0 (0 cm) 0 (0 cm) Closet 0 (0 cm) 0 (0 cm) 1 (2.54 cm) Closet door ventilation required: 2 louvered openings each 60 square inches (387 square centimeters) - 3 inches (7.6 cm) from bottom and top of door. This dryer MUST be exhausted outdoors. 5. The following illustrations show minimum clearance dimensions for proper operation in a recess or closet installation. 0" (0 cm) 60 sq. inches (387.1 sq. cm) 0" (0 cm) 60 sq. inches (387.1 sq. cm) 1" (2.54 cm) 0" (0 cm) CLOSET DOOR 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
5
CLOSET DOOR
60 sq. inches
(387.1 sq. cm)
60 sq. inches
(387.1 sq. cm)
0" (0 cm)
0" (0 cm)
0" (0
cm)
1" (2.54 cm)
LOCATION OF YOUR DRYER
DO NOT INSTALL YOUR DRYER:
1.
In an area exposed to dripping water or outside weather conditions.
2.
In an area where it will come in contact with curtains, drapes, or anything that will obstruct the flow of combustion and
ventilation air.
3.
On carpet. Floor
MUST
be solid with a maximum slope of 1 inch (2.54 cm).
INSTALLATION IN RECESS OR CLOSET
1.
A dryer installed in a bedroom, bathroom, recess or closet,
MUST
be exhausted outdoors.
2.
No other fuel burning appliance shall be installed in the same closet as the Gas dryer.
3.
Your dryer needs the space around it for proper ventilation.
DO NOT install your dryer in a closet with a solid door.
4.
A minimum of 120 square inches (774.2 square cm) of opening, equally divided at the top and bottom of the door, is required.
Air openings are required to be unobstructed when a door is installed. A louvered door with equivalent air openings for the full
length of the door is acceptable.
MINIMUM INSTALLATION CLEARANCES - Inches (cm)
SIDES
REAR
TOP FRONT
Alcove
0 (0 cm)
0 (0 cm)
Closet
0 (0 cm)
0 (0 cm)
1 (2.54 cm)
Closet door ventilation required:
2 louvered openings each 60 square inches (387 square centimeters) — 3 inches (7.6 cm) from
bottom and top of door.
This dryer MUST be exhausted outdoors.
5.
The following illustrations show minimum clearance dimensions for proper operation in a recess or closet installation.
5.
A 1/8 inch (0.32 cm) N.P.T. plugged tapping, accessible for test gauge connection,
MUST
be installed immediately upstream
of the gas supply connection to the dryer.
6.
The dryer
MUST
be disconnected from the gas supply piping system during any pressure testing of the gas supply piping system
at test pressures in excess of 1/2 psig (3.45 kPa).
7.
The dryer
MUST
be isolated from the gas supply piping system during any pressure testing of the gas supply piping system
at test pressures equal to or less than
1/2 psig (3.45 kPa).