Epson ActionPC 5000 User Manual - Page 29

Starting the SETUP Program, Press F2 to run SETUP.

Get Epson ActionPC 5000 PDF manuals and user guides View all Epson ActionPC 5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Q Automatic or manual selection of advanced hardware features for optimizing system performance Q System booting options Cl Security password and anti-virus features Q Green PC options, such as the time intervals before the system and the hard disk drive go into low-power standby mode. SETUP also provides summary information about your system. The SETUP program and the factory default options for your computer are stored in the computer's ROM (read-only memory). The configuration information you enter is backed up by a battery, so it is not erased when you turn off or reset the computer. Starting the SETUP Program When you start your computer, it performs some power-on diagnostics. During these diagnostics, you may see the following message: Press to enter SETUP Press F2 to run SETUP. This message is only on the screen for a few seconds. If you missed it, restart your computer and try again. (If you want, you can disable this message in SETUP.) If, during power-on diagnostics, the system detects an error in your system configuration, you hear two beeps and see an error message followed by this message: Press to resume, to run SETUP Press F2 to run SETUP. 2-2 Running SETUP and Installing Drivers

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
Q
Automatic or manual selection of advanced hardware
features for optimizing system performance
Q
System booting options
Cl
Security password and anti-virus features
Q
Green PC options, such as the time intervals before the
system and the hard disk drive go into low-power standby
mode.
SETUP also provides summary information about your system.
The SETUP program and the factory default options for your
computer are stored in the computer’s ROM (read-only
memory). The configuration information you enter is backed
up by a battery, so it is not erased when you turn off or reset
the computer.
Starting the SETUP Program
When you start your computer, it performs some power-on
diagnostics. During these diagnostics, you may see the
following message:
Press <F2> to enter SETUP
Press F2 to run SETUP. This message is only on the screen for a
few seconds. If you missed it, restart your computer and try
again. (If you want, you can disable this message in SETUP.)
If, during power-on diagnostics, the system detects an error in
your system configuration, you hear two beeps and see an
error message followed by this message:
Press <F1> to resume, <F2> to run SETUP
Press F2 to run SETUP.
2-2
Running SETUP and Installing Drivers