Epson EMP 730 User Manual - Page 59

Cleaning and Replacing the Air Filter - lamp replacement

Get Epson EMP 730 - XGA LCD Projector PDF manuals and user guides View all Epson EMP 730 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Cleaning and Replacing the Air Filter Clean the air filter on the side of the projector after every 100 hours of use. If it is not cleaned periodically, it can become clogged with dust, preventing proper ventilation. This can cause overheating and damage the projector. To clean the air filter, follow these steps: 1. Turn off the projector, allow it to cool down, and unplug the power cord. 2. To prevent dust from falling into the projector, place the projector as shown below. 3. To clean the filter, EPSON recommends using a small vacuum cleaner designed for computers and other office equipment. If you don't have one, gently clean the filter using a very soft brush (such as an artist's camel-hair brush). If the dirt is difficult to remove or if the filter is torn, replace it. Contact your dealer or call EPSON at (800) 873-7766 to obtain a new one. In Canada, please call (800) 463-7766 to locate a dealer. 4. If you need to replace the filter, lift the tab and pull it upward to remove the filter. note When you get a replacement lamp for your projector, a new air filter is included. You should replace the filter when you replace the lamp. 5. To install the new filter, first insert the tabs, then press down on the opposite end of the filter until it clicks in place. Maintaining and Transporting the Projector 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Maintaining and Transporting the Projector
53
Cleaning and Replacing the Air Filter
Clean the air filter on the side of the projector after every 100 hours of
use. If it is not cleaned periodically, it can become clogged with dust,
preventing proper ventilation. This can cause overheating and damage
the projector. To clean the air filter, follow these steps:
1.
Turn off the projector, allow it to cool down, and unplug the
power cord.
2.
To prevent dust from falling into the projector, place the
projector as shown below.
3.
To clean the filter, EPSON recommends using a small vacuum
cleaner designed for computers and other office equipment. If you
don’t have one, gently clean the filter using a very soft brush (such
as an artist’s camel-hair brush).
If the dirt is difficult to remove or if the filter is torn, replace it.
Contact your dealer or call EPSON at (800) 873-7766 to obtain a
new one. In Canada, please call (800) 463-7766 to locate a dealer.
4.
If you need to replace the filter, lift the tab and pull it upward to
remove the filter.
5.
To install the new filter, first insert the tabs, then press down on
the opposite end of the filter until it clicks in place.
note
When you get a replacement
lamp for your projector, a
new air filter is included.
You should replace the filter
when you replace the lamp.