Epson EPL-8000 Product Information Guide - Page 7

lever pivots outward.

Get Epson EPL-8000 PDF manuals and user guides View all Epson EPL-8000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

3. Press the chip into the socket as described in steps 3 and 4 of the previous section. 4. Set the board's DIP switches to indicate the amount of memory you have installed. Use a pointed object, such as a ball-point pen, to set the DIP switches as shown below. EPL-8000 Reinstalling the controller board 1. Hold the controller board so the component side faces your left, and fit its top and bottom edges into the grooves inside the slot. Gently slide the board about halfway into the printer. Set the switches according to the tables below. RAM (~ntemal and amount added lo controller board1 pqqigjq 2. Make sure the lever on the bottom of the controller board is a11 the way down. As you slide the board further into the printer, make sure the lever's tab is positioned inside the opening in the bracket. as shown below. 31 Installing the expansion board on the controller board 1. Locate connector chJ3 on the controller board. position the memory expansion board as shown below, and carefully insert its connector into connector CN3. Now slide the controller board into the printer. The lever pivots outward. Firmly press up on the lever to lock the board into pIace. If the controller board does not fit smoothly into the printer, do not force it. Remove it and make sure the edges fit properly into the grooves in the slot. Gently press in on the baud to make sure it is fully seated. Then secure the board with the four screws you removed previously. 2. Secure the expansion board with the three screws that came with it. 5. Replace the optional interface card, if you removed one 6 Connect any interface cables you removed. 7. Be sure the power is turned off and then plug the power cord into the printer and into an electrical outlet. Laser Printers ml92 EPL-8000-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
EPL-8000
3.
Press the chip into the socket as described in steps 3 and 4 of
the previous section.
4.
Set the board’s DIP switches to indicate the amount of memory
you have installed. Use a pointed object, such as a ball-point
pen, to set the DIP switches as shown below.
Set the switches according to the tables below.
RAM
(~ntemal
and amount
added
lo controller
board1
pqqigjq
31
Installing the expansion board on the controller board
1. Locate connector
chJ3
on the controller board. position the
memory expansion board as shown below, and carefully insert
its connector into connector
CN3.
2.
Secure the expansion board with the three screws that came
with it.
Reinstalling the controller board
1.
2.
5.
6
7.
Hold the controller board so the component side faces your
left, and fit its top and bottom edges into the grooves inside
the slot. Gently slide the
board
about halfway
into the printer.
Make sure the lever on the bottom
of
the controller
board is
a11
the
way down. As you slide the board further into
the
printer,
make sure the lever’s tab is positioned inside the opening in
the bracket. as shown below.
Now slide the controller board into the printer.
The
lever pivots outward.
Firmly press
up on the lever to
lock the
board into
pIace.
If the controller board does not fit smoothly into the printer,
do not force it. Remove it and make sure the edges fit properly
into the grooves in the slot.
Gently press in on the
baud
to make sure it is fully seated.
Then secure the
board
with the four screws you removed
previously.
Replace
the optional interface card, if you removed one
Connect any interface cables you removed.
Be sure
the power
is turned off and then plug the power cord
into the printer and into an electrical outlet.
Laser Printers
ml92
EPL-8000-7