Epson J7100 User Manual - Page 18

MICR Reading (Factory installed option only for the TMJ7000/J7100), Cleaning the MICR Mechanism

Get Epson J7100 - TM Two-color Inkjet Printer PDF manuals and user guides View all Epson J7100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

English MICR Reading (Factory installed option only for the TM-J7000/J7100) CAUTION: Do not insert checks with staples in them. This may cause paper jams, MICR reading errors, and damage to the MICR head. Never open the roll paper cover while the MICR reader is being used. Be sure the checks are flat, without curls, folds, or wrinkles. Do not use multipart checks. 1. Wait until the CUT SHEET LED blinks. Then insert the check face up with the right side of the check against the right side of the paper guide as far as it will go. Be sure that the MICR characters are on the right, as shown by the arrow in illustration L. 2. The printer will detect the check and start drawing it in. When the printer starts drawing it in, let go of the check immediately. When the printer ejects the check and the CUT SHEET LED starts blinking again; remove the check by pulling it straight up; do not pull it at an angle. Cleaning the MICR Mechanism Approximately every 12 months clean the MICR head with a moistened cleaning sheet. Use the following or an equivalent commercially available cleaning sheet: PRESAT brand (KIC) "CHECK READER CLEANING CARD." Note: Be sure not to use an adhesive cleaning sheet. Follow the steps below: 1. Load roll paper in the printer; turn off the power; then open the roll paper cover and turn the power back on while holding down the CLEANING button. 2. Press the CLEANING button 7 times; then close the paper roll cover. The printer prints the following message on the roll paper and the CUT SHEET LED flashes. **** RECOGNITION MODE **** Please set check. 3. Insert the cleaning sheet like a standard check. CAUTION: Be sure that the sheet is inserted with the correct side up and that it is inserted in the correct direction. Use a cleaning sheet only one time; then discard it. 10 TM-J7000/J7100 - TM-J7500/J7600 User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
10
TM-J7000/J7100 – TM-J7500/J7600 User’s Manual
English
MICR Reading (Factory installed option only for the
TM-J7000/J7100)
CAUTION:
Do not insert checks with staples in them. This may cause paper jams, MICR
reading errors, and damage to the MICR head.
Never open the roll paper cover while the MICR reader is being used.
Be sure the checks are flat, without curls, folds, or wrinkles.
Do not use multipart checks.
1.
Wait until the
CUT SHEET
LED blinks. Then insert the check
face up
with the
right side of the check against the right side of the paper guide as far as it will
go. Be sure that the MICR characters are on the right, as shown by the arrow
in illustration
L
.
2.
The printer will detect the check and start drawing it in. When the printer
starts drawing it in, let go of the check immediately. When the printer ejects
the check and the
CUT SHEET
LED starts blinking again; remove the check by
pulling it straight up; do not pull it at an angle.
Cleaning the MICR Mechanism
Approximately every 12 months clean the MICR head with a moistened cleaning
sheet.
Use the following or an equivalent commercially available cleaning sheet:
PRESAT brand (KIC) “CHECK READER CLEANING CARD.”
Note:
Be sure not to use an adhesive cleaning sheet.
Follow the steps below:
1.
Load roll paper in the printer; turn off the power; then open the roll paper
cover and turn the power back on while holding down the
CLEANING
button.
2.
Press the
CLEANING
button 7 times; then close the paper roll cover. The
printer prints the following message on the roll paper and the
CUT SHEET
LED flashes.
****
RECOGNITION MODE
****
Please set check.
3.
Insert the cleaning sheet like a standard check.
CAUTION:
Be sure that the sheet is inserted with the correct side up and that it is
inserted in the correct direction.
Use a cleaning sheet only one time; then discard it.