Epson MovieMate 55 User's Guide - Page 41

Viewing Status Information and Resetting the Lamp Timer, to exit the menu. - replacement lamps

Get Epson MovieMate 55 PDF manuals and user guides View all Epson MovieMate 55 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

You can adjust the following items: ■ Video Signal: Normally, you can leave this set to Auto when using external equipment. If no image appears or you see interference, select the appropriate signal. ■ Child Lock: Turn this setting on to lock the page 37 for more information. button on the control panel. See ■ Ceiling Projection: Turn this setting on to invert the image for viewing on the ceiling. (Requires a special optional adapter.) ■ High Altitude Mode: Turn this setting on if you use Epson MovieMate at an altitude above 4900 feet (1500 meters), to ensure that Epson MovieMate does not overheat. ■ Zoom: Select Wide to enlarge the image or Tele to reduce it. These settings work the same as the W and T arrows on the control panel. 4. Press or to adjust the setting. 5. Press to exit the menu. Viewing Status Information and Resetting the Lamp Timer You can use the Info page on the Visual Setup menu to view the number of hours the lamp has been used, and to reset the timer after you install a new lamp. You can also view video signal information and error codes for any problems that occur. 1. Press on the remote control. You see the Visual Setup menu. 2. Press to highlight Info, then press information. to display the lamp usage and other Note: If the lamp has been used less than 10 hours, 0H is displayed. 3. To reset the lamp timer after replacing the lamp, press . 4. Press to exit. Doing More with Epson MovieMate 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
Doing More with Epson MovieMate
41
You can adjust the following items:
■
Video Signal:
Normally, you can leave this set to
Auto
when using external
equipment. If no image appears or you see interference, select the appropriate signal.
■
Child Lock:
Turn this setting
on to
lock the
button on the control panel. See
page 37 for more information.
■
Ceiling Projection:
Turn this setting on to invert the image for viewing on the
ceiling. (Requires a special optional adapter.)
■
High Altitude Mode:
Turn this setting on if you use Epson MovieMate at an
altitude above 4900 feet (1500 meters), to ensure that Epson MovieMate does not
overheat.
■
Zoom:
Select
Wide
to enlarge the image or
Tele
to reduce it. These settings work
the same as the
W
and
T
arrows on the control panel.
4.
Press
or
to adjust the setting.
5.
Press
to exit the menu.
Viewing Status Information and Resetting the Lamp Timer
You can use the Info page on the Visual Setup menu to view the number of hours the lamp
has been used, and to reset the timer after you install a new lamp. You can also view video
signal information and error codes for any problems that occur.
1.
Press
on the remote control. You see the Visual Setup menu.
2.
Press
to highlight
Info
, then press
to display the lamp usage and other
information.
Note:
If the lamp has been used less than 10 hours, 0H is displayed.
3.
To reset the lamp timer after replacing the lamp, press
.
4.
Press
to exit.