Epson PP 100 User Guide - Page 17

Publishing Discs, Introduction, Turning power on/off - a

Get Epson PP 100 - Discproducer - DVD Duplicator x2 PDF manuals and user guides View all Epson PP 100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Chapter 2 Publishing Discs Introduction This section guides you through the procedures for creating and printing CDs/DVDs. Note: For information on CDs/DVDs, see the following section. & See "Discs" on page 90. Turning power on/off This section describes how to turn on/off power. Turning power on 1. Connect the power cable. 2. Press P power button until the power light flashes. Power light flashes in green, then stays on. Turning power off Press the P power button for more than 1 second. The then turn off; then power is turned off. power light will flash in green c Caution: ❏ Fan will operate after turning power off, but it will automatically stop after 15 minutes. ❏ If the product is operating, wait for 10 seconds after operation is stopped, then turn off power. ❏ The product may not be recognized by the computer when the power is turned back on while fan is operating. In this case, disconnect the USB cable and connect it again. Note' ❏ If turning off the product while power on the PC is on, follow the procedure below. If the product is turned off without following the procedure, data in the PC maybe damages. 1. If Total Disc Maker, Total Disc Monitor, or Total Disc Setup is running, close the application. 2. Double click "Safely Remove Hardware" on the task tray. 3. Select DVD drive on the product and select Stop. Publishing Discs 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
Publishing Discs
17
Chapter 2
Publishing Discs
Introduction
This section guides you through the procedures for creating and printing CDs/DVDs.
Note:
For information on CDs/DVDs, see the following section.
&
See “Discs” on page 90.
Turning power on/off
This section describes how to turn on/off power.
Turning power on
1.
Connect the power cable.
2. Press
P
power
button until the power light flashes.
Power light flashes in green, then stays on.
Turning power off
Press the
P
power
button for more than 1 second. The
power light will flash in green
then turn off; then power is turned off.
c
Caution:
❏
Fan will operate after turning power off, but it will automatically stop after 15 minutes.
❏
If the product is operating, wait for 10 seconds after operation is stopped, then turn off
power.
❏
The product may not be recognized by the computer when the power is turned back on
while fan is operating. In this case, disconnect the USB cable and connect it again.
Note’
❏
If turning off the product while power on the PC is on, follow the procedure below. If the product
is turned off without following the procedure, data in the PC maybe damages.
1.
If Total Disc Maker, Total Disc Monitor, or Total Disc Setup is running, close the application.
2. Double click "Safely Remove Hardware" on the task tray.
3. Select DVD drive on the product and select
Stop
.