Epson PS-100 Pulsense Band Quick Start - Page 1

Pulsense™ PS-100 Quick Start Read these instructions before using your product. Charge your product Before using your product for the first time, make sure the battery is fully charged. Charging takes approximately 1.5 to 2.5 hours. A full charge lasts about 36 hours. Caution: Do not attach the charging cradle when the PS-100 is wet. If the PS-100 is wet, wipe it with a damp cloth, remove the moisture with a towel, then let it air dry before attaching the charging cradle. 1. Center the PS-100 under the large tab, then press down until it clicks into place. 2. Insert the USB plug into a power source. You can use: ■ Computer (USB is for charging only, not for data transfer) ■ Optional USB AC Adapter (part number SFAC04) The orange LED lights up when your PS-100 is connected correctly. Charging is complete when the blue LED is lit. 3. Follow the on-screen instructions to pair your PS-100 with your mobile device and perform the initial configuration. The PS-100 can store up to 480 hours of data before needing to be synced. App icon Meaning No network connection. Make sure you have a network or data connection, then tap the icon to reconnect. No Bluetooth connection. Make sure Bluetooth is enabled on your product and mobile device, then tap the icon to reconnect. LED status The LEDs on the PS-100 light up or flash to indicate different states. When exercising, the LEDs indicate which zone you're currently in. The PS-100 vibrates when entering or leaving a zone. Light pattern Status Heart rate is below the fat burning zone Heart rate is approaching the fat burning zone Heart rate is in the fat burning zone Heart rate is in the aerobic exercise zone Heart rate is in the anaerobic exercise zone Heart rate is above the anaerobic exercise zone (flashing rapidly) The battery is low Airplane mode Wearing and Caring Instructions Follow these steps to adjust the wristband: 1. Unfasten the buckle of the wristband. Blue Orange To remove your PS-100 from the charging cradle, press the small tab down and push the PS-100 out from the back. 2. Unhook the band and adjust it to fit your wrist. Keep these tips in mind when wearing your PS-100: ■ When wearing the PS-100, make sure it does not touch the ulna bone. Ulna bone Install Epson PULSENSE View Download Epson PULSENSE View from your mobile device's app store. The following mobile devices are supported: ■ iPhone 4s, iPhone 5, iPhone 5c, or iPhone 5s with iOS 7.1 or later ■ Mobile device running AndroidTM 4.3 or later with Bluetooth® Smart Launch the app and pair your PS-100 You must pair your PS-100 through the Epson PULSENSE View app. The PS-100 will not store any data until you've paired it with the app. Follow these steps: 1. Start the Epson PULSENSE View app. 2. Make sure that the PS-100 is within 3 feet (1 meter) of the mobile device. ■ For greater accuracy, wear the Pulsense band on your non-dominant wrist. ■ Before boarding an aircraft, put your PS-100 in airplane mode by repeatedly tapping the top of the band. Your Pulsense product is made from materials commonly used in watches and other consumer products. Since you may wear your product over extended periods, including when you are exercising and sweating, it is important that you take care of your skin and your product according to these instructions. Prolonged wearing of your product without proper care could lead to skin irritation or rash. Please follow the precautions below to ensure full enjoyment and benefit of your Pulsense product: 1. Keep Pulsense and skin clean 2. Keep Pulsense and skin dry 3. Give skin a rest and some air See the online User's Guide for more instructions, including additional instructions on how to wear the band. Caution: Persons with high skin sensitivity, eczema, allergies, or asthma may be more likely to experience skin irritation or an allergic reaction from the Pulsense product or similar products. Even persons without such conditions may start to experience