Epson Perfection 3200 Photo Product Information Guide - Page 2

Electrical, Environmental, Safety Approvals, USB Interface, FireWire Interface, Transparency Unit - scanning negatives

Page 2 highlights

EPSON Perfection 3200 Series Electrical Input voltage range 100-120 VAC Rated input current 0.45 A Power consumption Approx. 24 W operating approx. 19 W in stand-by mode approx. 5.5 W in power saving mode Note: Scanners sold outside the US market may operate at a different voltage. Check the label on the back of the scanner for voltage information. Environmental Temperature Humidity (without condensation) Operating conditions Operation: 41 to 95 °F (5 to 35 °C) Storage: -13 to 140 °F (-25 to 60 °C) Operation: 10% to 80% Storage: 10% to 85% Ordinary office or home conditions; avoid extreme dust, direct sunlight, and strong light sources. Safety Approvals Safety EMC UL 1950 CSA C22.2 No. 950 FCC part 15 subpart B class B CSA C108.8 class B USB Interface Interface type Connector type Electrical standard Universal Serial Bus Specification Revision 2.0 One receptacle (Type B) Full Speed mode (12 Mbps) and High Speed mode (480 Mbps), Universal Serial Bus Specification Revision 2.0 Connector pin arrangement Pin number 1 2 3 4 Signal VCC -DATA +DATA GND Connector FireWire Interface Interface type IEEE 1394a-2000 compatible Data transfer Transfer speed Synchronization Encoding/ Decoding Logic level Half-duplex data / strobe differential serial Average: 4 Mbytes/sec Peak: 50 Mbytes/sec (100 to 400 Mbps) Clock synchronization with DS-Link DS-Link 3.3. V Connector pin arrangement Pin number 1 2 3 4 5 6 Signal VCC GND TPB- TPB+ TPA- TPA+ Connector 2 46 1 35 Transparency Unit The transparency unit is built into the scanner lid. Electrical Supply voltage: DC 21.6 to 26.4 V Rated current: 0.5 A Document specifications Positive or negative film in the following sizes: 35 mm strips 35 mm slides 120/220 (6 × 9-cm) film 4 × 5-inch film Readable area 4 × 9 inches (102 × 230 mm) Scanning Transparencies and Film Before scanning transparent documents, you need to remove the scanner's reflective document mat; this exposes the scanner's transparency unit (light source), which is built into the lid. If you're scanning slides or film strips, you'll also need to use one of the film holders. 2 - EPSON Perfection 3200 Series 11/02

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6

EPSON Perfection 3200 Series
2 - EPSON Perfection 3200 Series
11/02
Electrical
Input voltage
100-120 VAC
range
Rated input
0.45 A
current
Power
Approx. 24 W operating
consumption
approx. 19 W in stand-by mode
approx. 5.5 W in power saving mode
Note:
Scanners sold outside the US market may operate at a different
voltage. Check the label on the back of the scanner for voltage
information.
Environmental
Temperature
Operation: 41 to 95 °F (5 to 35 °C)
Storage: –13 to 140 °F (–25 to 60 °C)
Humidity
Operation: 10% to 80%
(without
Storage: 10% to 85%
condensation)
Operating
Ordinary office or home conditions; avoid
conditions
extreme dust, direct sunlight, and strong
light sources.
Safety Approvals
Safety
UL 1950
CSA C22.2 No. 950
EMC
FCC part 15 subpart B class B
CSA C108.8 class B
USB Interface
Interface type
Universal Serial Bus Specification
Revision 2.0
Connector type
One receptacle (Type B)
Electrical
Full Speed mode (12 Mbps) and High
standard
Speed mode (480 Mbps),
Universal
Serial Bus Specification Revision 2.0
Connector pin arrangement
FireWire Interface
Interface type
IEEE 1394a-2000 compatible
Data transfer
Half-duplex data / strobe differential
serial
Transfer speed
Average: 4 Mbytes/sec
Peak: 50 Mbytes/sec
(100 to 400 Mbps)
Synchronization
Clock synchronization with DS-Link
Encoding/
DS-Link
Decoding
Logic level
3.3. V
Connector pin arrangement
Transparency Unit
The transparency unit is built into the scanner lid.
Electrical
Supply voltage: DC 21.6 to 26.4 V
Rated current: 0.5 A
Document
Positive or negative film in the following
specifications
sizes:
35 mm strips
35 mm slides
120/220 (6
×
9-cm) film
4
×
5-inch film
Readable area
4
×
9 inches (102
×
230 mm)
Scanning Transparencies and Film
Before scanning transparent documents, you need to remove
the scanner’s reflective document mat; this exposes the scanner’s
transparency unit (light source), which is built into the lid.
If you’re scanning slides or film strips, you’ll also need to use
one of the film holders.
Pin number
Signal
Connector
1
VCC
2
DATA
3
+DATA
4
GND
Pin number
Signal
Connector
1
VCC
2
GND
3
TPB–
4
TPB+
5
TPA–
6
TPA+
1
3
5
6
4
2