Epson PowerLite 535W Quick Setup - Page 2

Adjust the image, Using the remote control, Project wirelessly from acomputer

Get Epson PowerLite 535W PDF manuals and user guides View all Epson PowerLite 535W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

Adjust the image 1 If you don't see an image, press the Source Search button on the projector or the remote control to select the image source.  Note: If you still see a blank screen or have other display problems, see the troubleshooting tips on the back of this sheet. 2 To raise the image, press the foot release button and lift the front of the projector. Release the button to lock the foot in position. Using the remote control Make sure the batteries are installed as shown (two AA batteries). Turn projector on and off Choose which source to display 3 Press the Wide or Tele buttons on the projector to reduce or enlarge the image. 4 Turn the focus ring to sharpen the image. 5 If your image looks like or , you may have placed the projector off to one side of the screen at an angle. Place the projector directly in front of the center of the screen, facing the screen squarely. If you can't move the projector, press the or button on the projector to open the keystone correction menu then use the Wide or Tele buttons to correct the image. 6 If your image looks like or , you can press the or button on the projector to correct it. Access projector menus Switch between computer and interactive pen Navigate projector menus Turn off projector display Get solutions to common problems For more information on using the remote control, see the online User's Guide. Project wirelessly from a computer Follow the steps here to connect the projector over a wireless network. You will need the optional wireless LAN module (part number V12H418P12). 1 To install the optional wireless LAN module, first remove the screw as shown. 2 Connect the wireless LAN module to the USB-A (flat) port. 3 To configure your projector for wireless projection, do one of the following: • If you're using the optional Quick Wireless Connection USB key (Windows only, part number V12H005M09), press the LAN button on the remote control. When you see SSID and IP address information on the screen, remove the wireless LAN module and connect the key to the projector's USB-A port. Look for the displayed message, remove the key, and connect it to a USB port on your computer. Follow your computer's on-screen instructions to install the driver, then reconnect the wireless LAN module to the projector's USB-A port. For details, see the online User's Guide. • If you're not using the key, continue with step 4.

  • 1
  • 2
  • 3
  • 4
Adjust the image
1
If you don’t see an image, press the
Source Search
button on the
projector or the remote control to select the image source.
Note:
If you still see a blank screen or have other display problems, see
the troubleshooting tips on the back of this sheet.
2
To raise the image, press the foot release button and lift the front of the
projector. Release the button to lock the foot in position.
3
Press the
Wide
or
Tele
buttons on the projector to reduce or enlarge the
image.
4
Turn the focus ring to sharpen the image.
5
If your image looks like
or
, you may have placed the projector
off to one side of the screen at an angle. Place the projector directly in
front of the center of the screen, facing the screen squarely. If you
can’t move the projector, press the
or
button on the projector to
open the keystone correction menu then use the
Wide
or
Tele
buttons to
correct the image.
6
If your image looks like
or
, you can press the
or
button on the projector to correct it.
Using the remote control
Make sure the batteries are installed as shown (two AA batteries).
Choose which
source to display
Turn projector
on and off
Access projector
menus
Turn off projector
display
Get solutions to
common problems
Navigate projector
menus
Switch between computer and
interactive pen
For more information on using the remote control, see the online
User’s
Guide
.
Project wirelessly from a
computer
Follow the steps here to connect the projector over a wireless network. You
will need the optional wireless LAN module (part number V12H418P12).
1
To install the optional wireless LAN module, first remove the screw as
shown.
2
Connect the wireless LAN module to the
USB-A
(flat) port.
3
To configure your projector for wireless projection, do one of the
following:
•
If you’re using the optional Quick Wireless Connection USB key
(Windows only, part number V12H005M09), press the
LAN
button on
the remote control. When you see SSID and IP address information
on the screen, remove the wireless LAN module and connect the
key to the projector’s
USB-A
port. Look for the displayed message,
remove the key, and connect it to a USB port on your computer.
Follow your computer’s on-screen instructions to install the driver,
then reconnect the wireless LAN module to the projector’s
USB-A
port. For details, see the online
User’s Guide
.
•
If you’re not using the key, continue with step 4.