Epson PowerLite 737c Product Information Guide - Page 14

Start the AirPort Admin utility. Select, Under Port Configurations, select - software

Get Epson PowerLite 737c PDF manuals and user guides View all Epson PowerLite 737c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Epson PowerLite 737c Projector 12.Verify that you've enabled your computer's connection to the access point. It should be listed as shown above, with the small icon next to it, indicating a connection. If it's not listed, click Configure and then type the name of your access point. 13.When done, click OK. Continue with "Projecting Wirelessly" on page 15. Checking the Gateway (Access Point's) IP Address If you're entering IP addresses manually in access point mode and need to find out the gateway IP address (the IP address of your access point), make sure the wireless connection to the access point is currently active, as described in the previous section. Note: If you can't identify the gateway address using this Windows utility, use the administrator's utility software that came with your access point. 1. Access your wireless network Properties window. For example, in Windows XP click Start > Control Panel > Network and Internet Connections. Then double-click the Network Connections icon. 2. Right-click the Wireless Network Connection icon and select Status. Then click the Support tab. The gateway's (access point's) IP address is listed as shown: Gateway address 2. Click the Network icon. You see the Network settings menu. Select Automatic Select Network Port Configurations then select AirPort 3. Make sure Location is set to Automatic. 4. Select Network Port Configurations in the Show pull- down menu. 5. Under Port Configurations, select AirPort. 6. Click Apply Now and close the window. 7. Ad hoc mode: Go to step 10. Access point mode: Start the AirPort Admin utility. Select your base station, then click Configure. 8. On the AirPort tab, make sure your AirPort network name matches your projector's ESSID. If not, enter the projector's ESSID in the AirPort Network text box and click Update. 9. If you turned DHCP in your projector's Advanced menu, click the Network tab and make sure the Distribute IP addresses checkbox is selected. If you need to select it, click Update. 10.Click the AirPort icon on the menu bar at the top of the Macintosh desktop. You see the AirPort status menu: Configuring the Network Settings for Macintosh Your AirPort software is automatically configured to allow your Macintosh to detect both computer-to-computer (ad hoc) and access point networks. Typically you only need to select your projector's ESSID (ad hoc) or your AirPort network name (access point) on the Macintosh menu bar. If you're having problems connecting to the projector, follow these steps: 1. From the Apple pull-down menu, select System Preferences. 11.Check to make sure AirPort is turned on. 12.Select your projector's ESSID (ad hoc) or the name of your AirPort network (access point). 14 - Epson PowerLite 737c Projector 2/05

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
Epson PowerLite 737c Projector
14
-
Epson PowerLite 737c Projector
2/05
12.Verify that you’ve enabled your computer’s connection to
the access point. It should be listed as shown above, with the
small icon
next to it, indicating a connection.
If it’s not listed, click
Configure
and then type the name of
your access point.
13.When done, click
OK
. Continue with “Projecting
Wirelessly” on page 15.
Checking the Gateway (Access Point’s) IP Address
If you’re entering IP addresses manually in access point mode
and need to find out the gateway IP address (the IP address of
your access point), make sure the wireless connection to the
access point is currently active, as described in the previous
section.
Note:
If you can’t identify the gateway address using this Windows
utility, use the administrator’s utility software that came with
your access point.
1.
Access your wireless network Properties window. For
example, in Windows XP click
Start > Control Panel >
Network and Internet Connections
. Then
double-click the
Network Connections
icon.
2.
Right-click the
Wireless Network Connection
icon and
select
Status
. Then click the
Support
tab.
The gateway’s (access point’s) IP address is listed as shown:
Configuring the Network Settings for Macintosh
Your AirPort software is automatically configured to allow
your Macintosh to detect both computer-to-computer (ad
hoc) and access point networks.
Typically you only need to select your projector’s ESSID (ad
hoc) or your AirPort network name (access point) on the
Macintosh menu bar. If you’re having problems connecting to
the projector, follow these steps:
1.
From the Apple pull-down menu, select
System
Preferences
.
2.
Click the
Network
icon. You see the Network settings
menu.
3.
Make sure Location is set to
Automatic
.
4. Select
Network Port Configurations
in the Show pull-
down menu.
5.
Under Port Configurations, select
AirPort
.
6. Click
Apply Now
and close the window.
7.
Ad hoc mode:
Go to step 10.
Access point mode:
Start the AirPort Admin utility. Select
your base station, then click
Configure
.
8.
On the AirPort tab, make sure your AirPort network name
matches your projector’s ESSID. If not, enter the projector’s
ESSID in the AirPort Network text box and click
Update
.
9.
If you turned DHCP in your projector’s Advanced menu,
click the
Network
tab and make sure the
Distribute
IP
addresses
checkbox is selected. If you need to select it, click
Update
.
10.Click the AirPort icon on the menu bar at the top of the
Macintosh desktop. You see the AirPort status menu:
11.Check to make sure AirPort is turned on.
12.Select your projector’s ESSID (ad hoc) or the name of your
AirPort network (access point).
Gateway
address
Select Automatic
Select Network Port
Configurations
then select AirPort