Epson PowerLite D6155W Quick Setup - Page 2

Adjust the image, Using the remote control, Project over a wired, network

Get Epson PowerLite D6155W PDF manuals and user guides View all Epson PowerLite D6155W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

Adjust the image 1 If you don't see an image, press the Source Search button on the projector or the remote control to select the image source. Note: If you still see a blank screen or have other display problems, see the troubleshooting tips on the back of this sheet. 2 To raise the image, press the foot release button and lift the front of the projector. Release the button to lock the foot in position. Project over a wired network Follow the steps here to configure your projector for your wired network using the projector's menu system. 1 Plug in and turn on the projector. 2 Press the Menu button on the remote control, select the Network menu, and press Enter. 3 Open the zoom/focus ring cover and rotate the focus ring to sharpen the image. Zoom/focus ring cover Focus ring 4 Turn the zoom ring to reduce or enlarge the image. Zoom ring 5 If your image looks like or , you've placed the projector off to one side of the screen at an angle. Place it directly in front of the center of the screen, facing the screen squarely. Or press the or buttons on the projector to correct it. 6 If your image looks like or , press the or buttons on the projector to correct it. Using the remote control Make sure the batteries are installed as shown (two AA batteries). 3 Select Network Configuration and press Enter. 4 Select the Basic menu and press Enter. 5 Select the Projector Name setting and enter a name (up to 16 characters long) to identify your projector over the network. Use the displayed keyboard to enter characters. Press the arrow buttons on the remote control to highlight the characters and press Enter to select them. Note: See the User's Guide on the projector CD for information on adding passwords. 6 Select the Wired LAN menu and press Enter. Turn projector on and off Turn off projector display and sound Access projector menus Choose which source to display Control projector volume Navigate projector menus For more information on using the remote control, see the User's Guide on your projector CD. 7 Choose IP Settings and press Enter. 8 If your network assigns addresses automatically, select IP Settings and turn on the DHCP setting. If not, turn off the DHCP setting and enter the projector's IP Address, Subnet Mask, and Gateway Address, as needed. 9 To prevent the IP address from appearing on the network standby screen, set the IP Address Display setting to Off.

  • 1
  • 2
  • 3
  • 4
Adjust the image
1
If you don’t see an image, press the
Source Search
button on the
projector or the remote control to select the image source.
Note:
If you still see a blank screen or have other display problems, see
the troubleshooting tips on the back of this sheet.
2
To raise the image, press the foot release button and lift the front of the
projector. Release the button to lock the foot in position.
3
Open the zoom/focus ring cover and rotate the focus ring to sharpen the
image.
Focus ring
Zoom/focus ring 
cover
4
Turn the zoom ring to reduce or enlarge the image.
Zoom ring
5
If your image looks like
or
, you’ve placed the projector off to
one side of the screen at an angle. Place it directly in front of the center
of the screen, facing the screen squarely. Or press the
or
buttons on
the projector to correct it.
6
If your image looks like
or
, press the
or
buttons on the
projector to correct it.
Using the remote control
Make sure the batteries are installed as shown (two AA batteries).
Choose which source 
to display
Turn projector 
on and off
Access projector 
menus
Turn off projector 
display and sound
Control projector 
volume
Navigate projector 
menus
For more information on using the remote control, see the
User’s Guide
on your
projector CD.
Project over a wired
network
Follow the steps here to configure your projector for your wired network
using the projector’s menu system.
1
Plug in and turn on the projector.
2
Press the
Menu
button on the remote control, select the
Network
menu, and press
Enter
.
3
Select
Network Configuration
and press
Enter
.
4
Select the
Basic
menu and press
Enter
.
5
Select the
Projector Name
setting and enter a name (up to 16
characters long) to identify your projector over the network.
Use the displayed keyboard to enter characters. Press the arrow buttons
on the remote control to highlight the characters and press
Enter
to
select them.
Note:
See the
User’s Guide
on the projector CD for information on
adding passwords.
6
Select the
Wired LAN
menu and press
Enter
.
7
Choose
IP Settings
and press
Enter
.
8
If your network assigns addresses automatically, select
IP Settings
and
turn on the
DHCP
setting. If not, turn off the
DHCP
setting and enter
the projector’s
IP Address
,
Subnet Mask
, and
Gateway Address
,
as needed.
9
To prevent the IP address from appearing on the network standby
screen, set the
IP Address Display
setting to
Off
.