Epson PowerLite Home Cinema 3000 Quick Setup - Page 3
Using the remote control, Viewing 3D images, Viewing WirelessHD content(PowerLite Home Cinema3600e
View all Epson PowerLite Home Cinema 3000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 3 highlights
Using the remote control Make sure the batteries are installed as shown (two AA batteries). Turn projector on Choose which source to display Switch between 2D and 3D Access projector menus Turn projector off Navigate projector menus You can also automatically convert 2D HDMI content to 3D (PowerLite Home Cinema 3500/3510/3600e). To enable the 2D-to-3D Conversion option, press the Menu button on the projector or remote control. Select Signal and press Enter, then select 3D Setup and press Enter. Select 2D-to-3D Conversion and press Enter. Select the Weak, Medium, or Strong setting, then press Enter. See the online User's Guide for more information on adjusting 3D images. Viewing WirelessHD content (PowerLite Home Cinema 3600e) 1 Turn on your video device and begin playback. 2 Turn on the power switch on the side of the WirelessHD Transmitter. 3 Turn on the projector. 4 If you have connected a television or other display to the output port on the transmitter and want to switch between wired and wireless display modes, press the Output button on the remote control or transmitter. The WiHD light on the transmitter will light up when the wireless display mode is active. Control WirelessHD functions (PowerLite Home Cinema 3600e only) For more information on using the remote control, see the online User's Guide. Viewing 3D images To view 3D content, you must first connect a 3D-compatible video device to one of the HDMI ports on your projector. You will also need a pair of Epson® (part number V12H548006) or Epson-compatible RF 3D active shutter glasses (included with PowerLite Home Cinema 3500/3510/3600e). 1 Turn on and begin playback on the 3D-compatible video device. Note: Make sure you set the video device to play content in 3D mode. 2 Press the 3D Format button on the remote control, if necessary. 3 Slide the power switch on your 3D glasses to the On position. Note: If the glasses don't automatically display 3D content, you may need to pair them with the projector. Move the glasses within 10 feet (3 m) of the projector, then press and hold the Pairing button on the 3D glasses for at least 3 seconds. The status light on the glasses will alternately flash green and red, then remain green for 10 seconds if pairing is successful. 5 Press the WirelessHD button on the remote control. Note: If the WirelessHD connection fails, press the Setup button on the bottom of the transmitter, then try again. 6 If you have connected multiple input devices to the transmitter, press the Input button on the remote control or transmitter once to display the sub-screen menu, then press the button again to switch between the input devices. 7 To display two WirelessHD input devices simultaneously, press the P-in-P button on the remote control to enable picture-in-picture mode. Press and hold the P-in-P button for three seconds to switch the main image and sub-screen, or press the P-in-P button again to disable picture-in-picture mode. See the online User's Guide for more information on adjusting and configuring the WirelessHD connection and display modes. Troubleshooting If you see a blank screen or the No signal message after turning on your video device or computer, check the following: •• Make sure the power light on the projector is blue and not flashing. •• Press the button on the projector or one of the Source buttons on the remote control to switch to the correct image source, if necessary. •• If you're using a Windows® laptop, press the function key on your keyboard that lets you display on an external monitor. It may be labeled CRT/LCD or have an icon such as . You may have to hold down the Fn key while pressing it (such as Fn + F7). Wait a moment for the display to appear. •• If you're using a Mac laptop, open System Preferences and select Displays. Click the Arrangement tab and select the Mirror Displays checkbox.