Epson Stylus Pro 4900 Quick Reference Guide - Page 9

Replacing Printer Parts continued, Replacing the Maintenance Tanks - new printer

Get Epson Stylus Pro 4900 PDF manuals and user guides View all Epson Stylus Pro 4900 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Replacing Printer Parts (continued) 5 Open the cutter cover. 6 Loosen the screw holding the cutter in place, then carefully remove the cutter. Warning: The blade is sharp. Be careful when removing it. 7 Insert the new cutter. Make sure the cutter pin goes into the hole. Tighten the screw using a cross-head screwdriver. Replacing the Ink Maintenance Tank 1 Open the right ink cartridge cover. 2 Pull out the maintenance tank as shown. Caution: Do not tilt the tank or ink may spill out 3 Place the used tank in the plastic bag included with the new tank and dispose of it carefully. 4 Insert the new tank, then close the cartridge cover. 8 Align the cutter cover, then press it in until it snaps into place. 9 Replace the front cover. Replacing the Borderfree Maintenance Tank 1 Remove the output tray. Note: If optional SpectroProofer is installed, remove it. 2 Release the tank lock. Note: If you are using the optional SpectroProofer, install it without replacing the front cover. 10 Close the printer cover and ink cartridge covers. 3 Pull out the maintenance tank as shown. Replacing the Maintenance Tanks The Epson Stylus Pro 4900 has two maintenance tanks: Ink (part# T619000) and Borderfree (part# T619100). You need to replace each maintenance tank when the LCD screen instructs you to do so. 1 Check the LCD screen to determine which tank needs to be replaced (Ink or Borderfree). Note: The printer will not print if one of the maintenance tanks is full. Caution: Do not tilt the tank or ink may spill out. 4 Place the used tank in the plastic bag included with the new tank and dispose of it carefully. 5 Insert the new tank. Push it in firmly. 6 Set the lock, then replace the output tray. 2 Turn off the printer. Note: The printer will not 8 print if the tank is unlocked.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
Replacing Printer Parts (continued)
8
8
Align the cutter cover, then press it in until it snaps
into place.
9
Replace the front cover.
Note:
If you are using the optional SpectroProofer,
install it without replacing the front cover.
10
Close the printer cover and ink cartridge covers.
Replacing the Maintenance Tanks
The Epson Stylus Pro 4900 has two maintenance tanks:
Ink (part# T619000) and Borderfree (part# T619100).
You need to replace each maintenance tank when the LCD
screen instructs you to do so.
1
Check the LCD screen to determine which tank needs
to be replaced (Ink or Borderfree).
Note:
The printer will not print if one of the
maintenance tanks is full.
2
Turn off the printer.
Replacing the Ink Maintenance Tank
1
Open the right ink cartridge cover.
2
Pull out the maintenance
tank as shown.
Caution:
Do not tilt the
tank or ink may spill out
3
Place the used tank in the plastic bag included with
the new tank and dispose of it carefully.
4
Insert the new tank, then close
the cartridge cover.
5
Open the cutter cover.
6
Loosen the screw holding the cutter in place, then
carefully remove the cutter.
Warning:
The blade is sharp. Be careful when
removing it.
7
Insert the new cutter. Make sure the cutter pin goes
into the hole. Tighten the screw using a cross-head
screwdriver.
Replacing the Borderfree Maintenance Tank
1
Remove the output tray.
Note:
If optional
SpectroProofer is
installed, remove it.
2
Release the tank lock.
3
Pull out the maintenance
tank as shown.
Caution:
Do not tilt the
tank or ink may spill out.
4
Place the used tank in the plastic bag included with the
new tank and dispose of it carefully.
5
Insert the new tank. Push
it in firmly.
6
Set the lock, then replace
the output tray.
Note:
The printer will not
print if the tank is unlocked.