Epson WorkForce ST-4000 Start Here - Installation Guide - Page 2

Load paper

Get Epson WorkForce ST-4000 PDF manuals and user guides View all Epson WorkForce ST-4000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

4 Wait for the ink to fill the tank. Do not squeeze the bottle. Ink flows into the tank and stops automatically when the ink is filled to the upper line. Note: If ink does not flow from the bottle, lift and reinsert the bottle. 5 When the ink tank is full, remove the ink bottle and securely close the ink tank cap. Place the remaining ink aside; you will need it later. 10 ST-3000: Press or to select your language on the LCD screen, then press the OK button. ST-4000: Select your language, country, and time. Note: You can change these settings later using the product's control panel. For more information, see the online User's Guide. Follow steps 11 and 12 to continue ink charging. 11 When the message to see the Start Here sheet appears on the LCD screen: ST-3000: Press the OK button, then press and hold the help button for 3 seconds. ST-4000: Press and hold the help button for 3 seconds. 12 When the ink confirmation message appears on the LCD screen, select Done to start charging the ink. Ink charging takes approximately 10 minutes. A message appears when ink charging is complete. Press the OK button to continue. Caution: Do not turn off the product, raise the scanner unit, or load paper while the product is charging or you'll waste ink. Note: Replace the bottle cap and tighten it. 6 Repeat the previous steps for the other colors. 7 Close the ink tank cover and then the scanner unit. 8 Connect the power cord to the back of the product and to an electrical outlet. Caution: Do not connect to your computer yet. 9 Raise the control panel, then press the power button to turn on the product. Note: The included ink bottles are designed for reliable printer setup and cannot be resold. After setup, the remaining ink is available for printing. 13 To complete filling the ink tanks, repeat steps 1 through 6 using the remaining ink in the bottles. Note: Replace the bottle cap before disposing of the bottles. 14 Close the ink tank cover and scanner unit. 15 Select Next and follow the on-screen instructions to reset the ink levels. 16 Follow the on-screen instructions to adjust the print quality. Press the OK button to continue. Note: You can change these settings later using the product's control panel. For more information, see the online User's Guide. 3 Load paper See the online User's Guide for information about loading capacity and available paper types and sizes. 1 Make sure the product is not charging, and then open the front of the paper cassette and pull out the paper cassette. Note: If an error message appears, turn off the product and check that no protective material has been left inside the product.

  • 1
  • 2
  • 3
  • 4
10
ST-3000:
Press
or
to select your language on the
LCD screen, then press the
OK
button.
ST-4000:
Select your language, country, and time.
Note:
You can change these settings later using the product’s
control panel. For more information, see the online
User’s Guide
.
Follow steps 11 and 12 to continue ink charging.
11
When the message to see the Start Here sheet appears
on the LCD screen:
ST-3000:
Press the
OK
button, then press and hold the
help button for
3 seconds
.
ST-4000:
Press and hold the
help button for
3 seconds
.
12
When the ink confirmation message appears on the LCD
screen, select
Done
to start charging the ink. Ink charging
takes approximately 10 minutes. A message appears
when ink charging is complete. Press the
OK
button to
continue.
Caution:
Do not turn off the product, raise the scanner unit, or
load paper while the product is charging or you’ll waste ink.
Note:
The included ink bottles are designed for reliable printer
setup and cannot be resold. After setup, the remaining ink is
available for printing.
13
To complete filling the ink tanks, repeat steps 1 through 6
using the remaining ink in the bottles.
Note:
Replace the bottle cap before disposing of the bottles.
14
Close the ink tank cover and scanner unit.
15
Select
Next
and follow the on-screen instructions to reset
the ink levels.
16
Follow the on-screen instructions to adjust the print
quality. Press the
OK
button to continue.
Note:
You can change these settings later using the product’s
control panel. For more information, see the online
User’s Guide
.
3
Load paper
See the online
User’s Guide
for information about loading
capacity and available paper types and sizes.
1
Make sure the product is not charging, and then open
the front of the paper cassette and pull out the paper
cassette.
4
Wait for the ink to fill the tank.
Do not squeeze the bottle.
Ink flows into the tank and stops automatically when the
ink is filled to the upper line.
Note:
If ink does not flow from the bottle, lift and reinsert the
bottle.
5
When the ink tank is full, remove the ink bottle and
securely close the ink tank cap. Place the remaining ink
aside; you will need it later.
Note:
Replace the bottle cap and tighten it.
6
Repeat the previous steps for the other colors.
7
Close the ink tank cover and then the scanner unit.
8
Connect the power cord to the back of the product and to
an electrical outlet.
Caution:
Do not connect to your computer yet.
9
Raise the control panel, then press the
power button to
turn on the product.
Note:
If an error message appears, turn off the product and
check that no protective material has been left inside the product.